Honda CBF600N Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 620

Honda CBF600N Скачать руководство пользователя страница 166

FUEL SYSTEM (PGM-FI)

5-52

7. Pull and release the rubber cap from the retainer.

8. Hold the connector with one hand and squeeze

the retainer tabs with the other hand to release
them from the locking pawls.
Pull the connector off, then remove the rubber
cap and retainer from the fuel joint.

• Prevent the remaining fuel in the fuel feed hose

from following out with a shop towel.

• Be careful not to damage the hose or other parts.
• Do not use tools.
• If the connector does not move, keep the retainer

tabs pressed down, and alternately pull and push
the connector until it comes of easily.

9. To prevent damage and keep foreign matter out,

cover the disconnected connector and fuel joint
end with the plastic bags.

QUICK CONNECT FITTING
INSTALLATION

• Always replace the retainer of the quick connect

fitting when the fuel feed hose is disconnected.

• If any damage or cut-out on the rubber cap,

replace it with a new one.

• Do not bent or twist fuel feed hose.

1. Insert a new retainer into the connector.

LOCKING PAWLS

CONNECTOR

RUBBER CAP

RETAINER TABS

PLASTIC BAGS

RETAINER

CONNECTOR

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
164
165
166
167
168
...
»

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов