Honda CBF600N Скачать руководство пользователя страница 516

Страница: 516 / 620

BATTERY/CHARGING SYSTEM

17-4

TROUBLESHOOTING

BATTERY IS DAMAGED OR WEAK

1. BATTERY TEST

Remove the battery (page 17-5).

Check the battery condition using the recommended battery tester.

Is the battery in good condition?

YES

–

GO TO STEP 2.

–

Faulty battery

2. CURRENT LEAKAGE TEST

Install the battery (page 17-5).

Check the battery current leakage test (Leak test; page 17-7).

Is the current leakage below 2.0mA?

YES

–

GO TO STEP 4.

–

GO TO STEP 3.

3. CURRENT LEAKAGE TEST WITHOUT REGULATOR/RECTIFIER CONNECTOR

Disconnect the regulator/rectifier connector and recheck the battery current leakage.

Is the current leakage below 2.0mA?

YES

–

Faulty regulator/rectifier

–

• Shorted wire harness
• Faulty ignition switch

4. ALTERNATOR CHARGING COIL INSPECTION

Check the alternator charging coil (page 17-8).

Is the alternator charging coil resistance within 0.1 – 1.0

Ω

(20

C/68

F)?

YES

–

GO TO STEP 5.

–

Faulty charging coil

5. CHARGING VOLTAGE INSPECTION

Measure and record the battery voltage using a digital multimeter (page 17-7).

Start the engine.

Measure the charging voltage (page 17-7).

Compare the measurement to result of the following calculation.

Is the measured charging voltage within the standard voltage?

YES

–

Faulty battery

–

GO TO STEP 6.

6. REGULATOR/RECTIFIER SYSTEM INSPECTION

Check the voltage and resistance at the regulator/rectifier connector (page 17-8).

Are the results of checked voltage and resistance correct?

YES

–

Faulty regulator/rectifier

–

• Open circuit in related wire
• Loose or poor contacts of related terminal
• Shorted wire harness

RECOMMENDED BATTERY TESTER:
BM-210 or BATTERY MATE or equivalent

STANDARD: Measured BV < Measured CV < 15.5 V

· BV = Battery Voltage (page 17-7)
· CV = Charging Voltage

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CBF600N

Отзывы:

Honda CBF600N, Руководство по обслуживанию, Страница: 516 / 620

Результаты поиска

Содержание CBF600N

Отзывы: