Honda CBF600N Скачать руководство пользователя страница 534 | Manualshive

Страница: 534 / 620

Honda CBF600N Скачать руководство пользователя страница 534

ELECTRIC STARTER

19-4

TROUBLESHOOTING

Starter motor does not turn

1. Fuse Inspection

Check for blown main fuse or sub fuse.

Did the fuse blow?

YES

–

Replace the fuse

NO

–

GO TO STEP 2.

2. Battery Inspection

Make sure the battery is fully charged and in good condition.

Is the battery in good condition?

YES

–

GO TO STEP 3.

NO

–

Replace the battery (page 17-5)

3. Starter Relay switch operation

Check the starter relay switch operation.
You should hear the relay “CLICK” when the starter switch button is depressed.

Did the starter relay "CLICK"?

YES

–

GO TO STEP 4.

NO

–

GO TO STEP 5.

4. Starter Motor Inspection

Apply battery voltage to the starter motor directly and check the operation.

Did the starter motor turn?

YES

–

• Poorly connected starter motor cable
• Faulty starter relay switch (page 19-15)

NO

–

Faulty starter motor (page 19-6)

5. Relay Coil Ground Wire Lines Inspection

Disconnect the starter relay switch connector, and check the relay coil ground wire lines as below for
continuity:

1. Green/red terminal-clutch switch diode – neutral switch line (with the transmission in neutral and

clutch lever released).

2. Green/red terminal-clutch switch – sidestand switch line (in any gear except neutral, and with the

clutch lever pulled in and the sidestand up).

Is there continuity?

YES

–

GO TO STEP 6.

NO

–

• Faulty neutral switch (page 20-35)
• Faulty clutch diode (page 19-17)
• Faulty clutch switch (page 20-34)
• Faulty sidestand switch (page 20-36)
• Loose or poor contact connector
• Open circuit in wire harness

6. Starter Relay Voltage Inspection

Connect the starter relay switch connector.

With the ignition switch ON and the starter switch pushed, measure the starter relay voltage at the
starter switch connector (between Yellow/red (+) and ground (–)).

Is the starter relay switch operation correct?

YES

–

GO TO STEP 7.

NO

–

• Faulty ignition switch (page 20-30)
• Faulty starter switch (page 20-32)
• Faulty engine stop switch (page 20-32)
• Loose or poor contact connector
• Open circuit in wire harness

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
532
533
534
535
536
...
»

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов