Honda CBF600N Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 620

Honda CBF600N Скачать руководство пользователя страница 128

FUEL SYSTEM (PGM-FI)

5-14

CLEARING DTC

Connect the HDS Pocket Tester to the DLC (page 5-13).

Clear the DTC with the HDS while the engine is stopped.

To clear the DTC without HDS, refer to the following procedure.

How to clear the DTC with SCS connector

1. Lift and support the fuel tank (page 3-5).

2. Turn the ignition switch to OFF.

3. Make sure the engine stop switch is turned to " ".

Remove the dummy connector and short the Brown and Green wire
terminals of the DLC using the special tool.

4. Turn the ignition switch to ON.

5. Remove the special tool wire from the DLC.

6. The MIL will light for approximately 5 seconds. While the MIL lights,

short the DLC terminals again with the special tool. The self-diag-
nostic memory is erased if the malfunction indicator goes off and starts blinking.

• The DLC must be jumped while the MIL lights. If not, the MIL will not start blinking.
• Note that the self-diagnostic memory cannot be erased if the ignition switch is turned to "OFF" before the MIL starts

blinking.

CIRCUIT INSPECTION

INSPECTION AT ECM CONNECTOR

• Always clean around and keep any foreign material away from the

ECM connector before disconnecting it.

• A faulty PGM-FI system is often related to poorly connected or cor-

roded terminals. Check those connections before proceeding.

• In testing at ECM connector (wire harness side) terminal, always

use the test probe. Insert the test probe into the connector terminal,
then attach the digital multimeter probe to the test probe.

TEST HARNESS CONNECTION

Turn the ignition switch to "OFF".

Remove the side cover (page 2-5).

Remove the screw.
Pull out the ECM from the stay.

TOOL:
SCS connector

070PZ-ZY30100

CONNECTION:

Brown – Green

TOOL:
Test probe

07ZAJ-RDJA110

SCS SERVICE CONNECTOR

DLC

TEST PROBE

SCREW

STAY

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
126
127
128
129
130
...
»

Содержание CBF600N













































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов