HNP Mikrosysteme mzr-2509 Ex Скачать руководство пользователя страница 54

Страница: 54 / 124

6 Mounting / Installation

Operation manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

Technische Änderungen ohne Vorankündigung vorbehalten

Last update: October 2016

6.10

Installation of the software »Motion Manager«

The program »Motion Manager« provides easy operation and configuration of

the motor together with an online graphic performance analysis tool. For

installation a PC with Windows XP

or Windows 7

is required.

Install the software »Motion Manager« which is included in the delivery CD.

After successful installation start the program »Motion Manager« in the file

»Faulhaber Motoren« via Windows

start menu.

If the diskettes of the »Motion Manager« are not delivered, because the

software »mzr-pump controller« was included instead, you can download the

software from the website

http://www.hnp-mikrosysteme.de

. The latest version

can be downloaded in English or German under

Downloads

To program a micro annular gear pump motor and controller have to be put

into operation. Both units have to be connected with the zero-modem cable.

Содержание mzr-2509 Ex





























































































































Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2509 Ex, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды