HNP Mikrosysteme mzr-2509 Ex Скачать руководство пользователя страница 30

Страница: 30 / 124

4 Description of the pump

Operation manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

Technische Änderungen ohne Vorankündigung vorbehalten

Last update: October 2016

4.4

Fluidic connectors

Liquid inlet/outlet

Tubing

mzr-2909 Ex,
mzr-4609 Ex

1/4"–28 UNF, front

OD 1/8" plastic tubes or stainless steel
tubes (optional outer diameter 1/16")

mzr-7209 Ex

lateral 1/8" NPT internal thread
front 1/8" NPT internal thread

tube/hose OD 6 mm

table 11

Liquid supply

The liquid inlet is marked with the letter »S«, the liquid outlet connection with

the letter »D«. An arrow indicates the inherent turning direction of the shaft.

For protection against penetrating dust particles and contamination, sealing

plugs are inserted into the threads. The sealing plugs have to be removed

before the assembly of the fluidic connectors. Please reseal the threads with the

cleaned sealing plugs when the fluidic connectors are disassembled.

The assembled fluid connectors have to be checked immediately after bringing

the pump into operation. This is also true for service in a half-yearly cycle on

tightness and leakage.

Содержание mzr-2509 Ex





























































































































Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2509 Ex, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды