HNP Mikrosysteme mzr-2509 Ex Скачать руководство пользователя страница 48

Страница: 48 / 124

6 Mounting / Installation

Operation manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

Technische Änderungen ohne Vorankündigung vorbehalten

Last update: October 2016

Installation of the cable wires

−

tool: screwdriver blade 2.5 x 0.4 mm

−

open the spring clamp with the screwdriver through the side
slot

−

cable in cable opening place (cable can be used with or without
ferrule)

−

remove the screwdriver

figure 21

Installation of cable wires in the connectors

LED Status

Definition

green

Power supply to the controller is active, no error

red

Motor error (current limitation or pump blocked)

table 20

LED for status indication

The operating speed of the micro annular gear pump may be set with:

−

the potentiometer of the Terminal Box S-G05

−

an external voltage signal 0-10 V

−

an external, analog current signal 0 (4)-20 mA (without electrical isolation)

−

an external potentiometer or

−

the RS-232 interface

Individual start up procedures are described in the following points.

6.9.1

Startup with potentiometer

Connect the drive with the eight colored wires to the terminal box S-G05.

The colors of the corresponding wire connections are described in the

table 26.

Bring the potentiometer knob to null position by turning it clockwise to the

limit stop.

Put the DIP-switch to the »Poti« position.

Connect the 24 VDC voltage supply to the terminal or to the DIN

connector.

Make sure that the polarity of the supplied direct current is correct, otherwise

electronics will be damaged.

Provide for a steady liquid supply to the pump in order to avoid dry

operation.

The pump may now be put into operation by turning on the potentiometer

knob.

Содержание mzr-2509 Ex





























































































































Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2509 Ex, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды