HNP Mikrosysteme mzr-2509 Ex Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 124

background image

10 Software »Motion Manager«

Operation manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

68

Technische Änderungen ohne Vorankündigung vorbehalten

Last update: October 2016

For saving of settings of the configuration or program sequence in the onboard

memory (EEPROM) answer the question »Should the EEPSAV command be

carried out and the transferred settings saved?« with »Yes«. At that time the

settings are written to the EEPROM. After switch on/off of the motion

controller settings and program is available.

The delivery volume comprises the standard program

mzr-2509_S.mcl,

mzr-2909_S.mcl,

mzr-4609_S.mcl

,

mzr-7209_S.mcl

and the sample programs

switchdosage_2509_S.mcl

,

switchdosage_2909_S.mcl

,

switchdosage_4609_S.mcl

and

switchdosage_7209_S.mcl

for triggered dosage

with an external switch.

The standard program

mzr-2509_S.mcl

(see Listing 1) is saved at delivery state

of the micro annular gear pump mzr-2509 Ex.

Upon delivery the motion controller is configured with following parameter:

−

Operation mode analogue input, Source for velocity via potentiometer

(Command SOR1)

−

Enable driver (Command EN)

−

Continuous mode (Command CONTMOD)

−

Maximum velocity 4700 U/min (Command SP4700)

−

Maximum peak current 800 mA (Command LPC800)

−

Maximum continuous current 600 mA (Command LCC600)

−

Acceleration 550 U/s² (Command AC550)

−

Fault pin as error output (Command ERROUT)

−

Asynchronous answer (Command ANSW1)

−

Clear program memory with no programs

; File:

mzr-2509_S.mcl

; Description:

Standard mcl-file for micro annular gear pump mzr-2509Ex

;

Speed is controlled by potentiometer of the connection panel

;

Fault as error output program

; Hardware:

Motion Controller S-HD-KL, Steuerung MCDC3006S, Schnittstelle RS-232

;
; Date:

2012-03-29

; Copyright © 2012, HNP Mikrosysteme GmbH, Parchim
;
; HNP Mikrosysteme GmbH, Juri-Gagarin-Ring 4, 19370 Parchim
; T49(0)3871/451-301, T49(0)3871/451-333
; Email [email protected], http://www.hnp-mikrosysteme.de
;
;--------------------------------------------------------------------------------------------------------------
; Configuration Motor
;--------------------------------------------------------------------------------------------------------------

SOR1

;Source For Velocity - Solldrehzahl über Potentiometer

CONTMOD

;Continuous Mode - Normalbetrieb

KN246

;Load Speed Constant - Drehzahlkonstante laden [rpm/V]

RM1230

;Load Motor Resistance - Motorwiderstand laden [mOhm]

APL0

;Position Limits - Positionslimits deaktivieren

MOTTYP8

;Motor Type - EC-Motor 3564K024B C

POHOSEQ0

;Power On Homing Sequence - Keine Homing-Sequenze nach dem

Einschalten
ERROUT

;Error Output - Umschalten auf Fehlerausgangsmodus

HP7

;Hard Polarity - alle Eingänge steigende Flanke gültig

HB0

;Hard Blocking - Kein Hard-Blocking

HD0

;Hard Direction - Für alle Endschalter Linkslauf sperren (falls Hard-Blocking

aktiv)

«
...
72
73
74
75
76
...
»

Содержание mzr-2509 Ex





























































































































Отзывы:

Нет отзывов

Похожие инструкции для mzr-2509 Ex

Бренд: Jandy Страницы: 52

Бренд: Samoa Страницы: 36

Бренд: Carrier Страницы: 30

Goulds CentriPro M05411

Бренд: Xylem Страницы: 68

Бренд: Waterax Страницы: 6

Everlast Elevate ELV055C2X055N

Бренд: HTP Страницы: 20

HTVZD*1C series

Бренд: Halsey Taylor Страницы: 7

Pro VSPHP270JEP

Бренд: Jandy Страницы: 20

ARO 66605J- Series

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Raider Страницы: 92

Бренд: JABSCO Страницы: 4

Бренд: Alfa Laval Страницы: 34

SKY PRO 10 CPC 58

Бренд: KU Solar Страницы: 50

Бренд: Danfoss Страницы: 20

Бренд: Sera Страницы: 47

Бренд: EBARA Страницы: 51

Бренд: Wallace Pumps Страницы: 5

Бренд: Viessmann Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды