HNP Mikrosysteme mzr-2509 Ex Скачать руководство пользователя страница 22

Страница: 22 / 124

2 Safety instructions

Operation manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

Technische Änderungen ohne Vorankündigung vorbehalten

Last update: October 2016

Safety instructions

Comply with the general safety instructions listed in the safety section as well

as with the special safety instructions listed under the other main sections. All

legal and corporate safety instructions have to be obeyed.

2.1

Labeling of instructions in the operation manual

The safety instructions listed in this operation manual are specially labeled. It

can cause danger for persons, if they are not complied with.

Danger symbol

Non-compliance poses danger for

persons.

High voltage

symbol

Non-compliance poses danger of

electrical shock.

Ex-symbol

These instructions must be complied

with in full for explosion-protection.

The type plate mounted on the pump must be complied with and has to be

maintained in a clearly readable condition.

Please pay attention to items marked with the following symbols. Pump or

system damage is possible if these warnings are ignored.

Warning

Information plates attached directly to the pump head

for example

name of

the fluid inlet/outlet, sign with the direction of rotation must be observed and

preserved.

2.2

Staff qualification and training

The staff for operation, maintenance, inspection and assembly must evidence

appropriate qualifications for these works. Areas of responsibility, competencies

and monitoring of the staff must be precisely regulated by the operating

company. If the personnel do not have the necessary knowledge, they must be

trained and instructed accordingly. If necessary this can be carried out by the

manufacturer / supplier on behalf. In addition, the operating company must

ensure that the content of this operating manual is fully understood by the

personnel.

Содержание mzr-2509 Ex





























































































































Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2509 Ex, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды