HNP Mikrosysteme mzr-2509 Ex Скачать руководство пользователя страница 68

Страница: 68 / 124

9 Problems and their removal

Operation manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

Technische Änderungen ohne Vorankündigung vorbehalten

Last update: October 2016

Disturbance

Cause

Solution

manufacturer.

17 The pump is noisy

Wearout of the pump or defective
components

Do not continue to operate the pump, return it
to the manufacturer for maintenance.

18 Lack of connection with the RS-232

interface

The pump is not connected.

Check the power supply 24 VDC.

Check the connection of the interface and the
null-modem cable. Change the cable if
necessary.

The drive control does not respond.

Interrupt the voltage supply for about 10 s,
connect the voltage supply again. Automatic
start of the integrated drive control

19 Overcurrent

Particles in the delivered liquid

Rinse the pump.

The pump operates with difficulty.

Dosing needle is damaged. Needle should be
cleansed, flushed or exchanged.

Tubing on the delivery side, dosing needle or
non-return valve are blocked. Cleanse, flush or
exchange the components.

Deposits inside the pump.

Flush the pump. If necessary return the pump
to the manufacturer.

20 Undervoltage

Voltage supply < 12 VDC

Check the power supply 24 VDC.

21 Overvoltage

Voltage supply > 28 VDC

Check the power supply 24 VDC. The drive
control may be damaged. Return the pump to
the manufacturer.

Table 26

Trouble shooting guide

If unknown faults appear or an uncertainty arises from appearing faults in the

working with the pump, immediately shut down the micro annular gear pump

at first!

Содержание mzr-2509 Ex





























































































































Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2509 Ex, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды