HNP Mikrosysteme mzr-2509 Ex Скачать руководство пользователя страница 39

Страница: 39 / 124

6 Mounting / Installation

Operating manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

Last update: October 2016

Technische Änderungen ohne Vorankündigung vorbehalten.

Warning

Take care at the mounting of the micro annular gear pump that in the fault

case leaking liquid cannot get into the motor or the control unit.

Take caution measures in the case of a leak so, that damage to adjacent

facilities and the ambient environment are avoided.

Never install a pump in a small installation location without sufficient

ventilation as the motor will be poorly cooled and can overheat.

The actuators must be protected against

moisture, dust and perspiration

6.4

Electrical Connections

The electrical connection of the motors must be implemented according to

VDE directives by skilled personnel. The operation manual supplied with the

motors must also be complied with.

Earth the motor using the terminal provided.

Earth the pump head with

heating module additionally at the corresponding terminal clamp.

6.5

Assembly instruction for tubing and accessories

Particles or soiling can block or impair the function of the micro annular gear

pump.

Warning

Please check that all wetted parts of the fluidic system are clean. Clean these

parts in case before mounting the pump.
Please check whether there are swarfs in the screw connections, pollution

remaining in reservoirs or soiling in valves, pipe work or filters.

Assembly of the tubing and piping system

Please cut the tubing rectangular with a hose cutter.

If metal pipes are used an intensive cleaning procedure is necessary. After

machining the pipes have to be cleaned and flushed very carefully. Smallest

swarfs within the fluidic system can cause failure of the micro annular gear

pump.

Connect the fittings with the tubing respectively the pipe work according to

the attached installation instruction.

In the next step seal the pipe fittings at the suction side and discharge side

of the pump head with PTFE tape. This is only valid for 1/8“ NPT inside

thread.

The thread of the fitting should be wrapped with 2-3 layers of PTFE tape

and screwed in the NPT thread (see table 15). First manually, then tightened

with ½ to ¾ wrench turns.

Содержание mzr-2509 Ex





























































































































Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2509 Ex, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды