HNP Mikrosysteme mzr-2509 Ex Скачать руководство пользователя страница 95

Страница: 95 / 124

Declaration of EC-Conformity

(following Machinery Directive 2006/42/EC)

We hereby declare that the following micro annular gear pumps of the high

performance series:

mzr-2509 Ex, mzr-2909 Ex, mzr-4609 Ex, mzr-7209 Ex,

mzr-2509X2 Ex, mzr-2909X2 Ex, mzr-4609X2 Ex, mzr-7209X2 Ex

are intended for installation into another machinery/plant and that start of

operation is forbidden until it is identified that the machinery/plant into which

these micro annular gear pumps shall be installed corresponds to the

regulations of the EC guidelines regarding safety and health requirements.

We confirm the conformity of the product described above to the following

standards in terms of applied directives

−

Directive 2006/42/EC (Community legislation on machinery)

Applied standards are particularly

DIN EN 809

DIN EN 60204-1

DIN EN ISO 13857

DIN EN ISO 12100 part 1

DIN EN 953

DIN EN ISO 12100 part 2

UVV

This statement does not warrant any characteristics in terms of product liability.

Please note the safety instructions in the manual.

Mr. Lutz Nowotka, HNP Mikrosysteme GmbH, Bleicherufer 25, D-19053

Schwerin is authorised to compile the technical file according to Annex VII A.

Date: 12. August 2016
Signature manufacturer:

Dr. Thomas Weisener

CEO

Содержание mzr-2509 Ex





























































































































Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2509 Ex, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды