HNP Mikrosysteme mzr-2509 Ex Скачать руководство пользователя страница 69

Страница: 69 / 124

10 Software »Motion Manager«

Operating manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

Last update: October 2016

Technische Änderungen ohne Vorankündigung vorbehalten.

Software »Motion Manager«

For the programming of the micro annular gear pump the software » Motion

Manager « must be installed (see section 6.8). The connection from controller

to PC with the delivered zero modem cable has to be established and the micro

annular gear pump have been taken into service.

10.1

Command mode

With software »Motion Manager« commands can be entered and sent directly

to the motion controller to change the settings of the controller or execute

movements.

Figure 28

Program »Motion Manager« for direct control commands for the micro annular gear pump

The entry of command lines takes place in the field »Enter command:«. When

the command entry is completed this must be confirmed by pressing the

button »Send« to send. The commands can alternatively be written in capital or

small letters. Surplus blanks are ignored by the motion controller.

Содержание mzr-2509 Ex





























































































































Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2509 Ex, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2509 Ex

Отзывы:

Похожие инструкции для mzr-2509 Ex

Бренды по названию

Популярные бренды