Hitachi L100 IP Series, Инструкция по эксплуатации

Страница: 92 / 94

Appendix B – Printed form for user defined parameter settings (remote operator)
B-4
Standard setting
Func.
No.
Function (Function mode) Display
-FE -FU
S e t v a l u e
Frequency lower limit LIMIT L 000.0Hz 0Hz 0Hz
F-26
Frequency upper limit LIMIT H 000.0Hz 0Hz 0Hz
1. jump frequency
JUMP F1 000.0Hz
0Hz 0Hz
2. jump frequency JUMP F2 000.0Hz 0Hz 0Hz
3. jump frequency JUMP F3 000.0Hz 0Hz 0Hz
1. jump frequency width JUMP W1 00.5Hz 0.5Hz 0.5Hz
2. jump frequency width
JUMP W2 00.5Hz
0.5Hz 0.5Hz
F-27
3. jump frequency width JUMP W3 00.5Hz 0.5Hz 0.5Hz
F-28 STOP key locking STOP-SW ON ON ON
External frequency start point IN EXS 000.0Hz 0Hz 0Hz
External frequency end point
IN EXE 000.0Hz
0Hz 0Hz
External frequency start point bias IN EX%S 000% 0% 0%
External frequency end point bias IN EX%E 100% 100% 100%
External frequency start pattern IN LEVEL 0Hz 0Hz 0Hz
F-31
Analog input filter time constant
IN F-SAMP 8
8 8
Arrival frequency FA2 for
acceleration
ARV ACC 000.0Hz 0Hz 0Hz
F-32
Arrival frequency FA2 for
deceleration
ARV DEC 000.0Hz
0Hz 0Hz
Level for overload signal
OV Load 16.50A
Rated
current
Rated
current
F-33
Level of PID deviation OV PID 003.0% 3% 3%
Function of digital input 1 IN-TM 1 FW FW FW
Function of digital input 2
IN-TM 2 RV
RV RV
Function of digital input 3 IN-TM 3 CF1 CF1 AT
Function of digital input 4 IN-TM 4 CF2 CF2 USP
Function of digital input 5 IN-TM 5 RS RS RS
Type of digital input 1
IN-TM O/C-1 NO
NO NO
Type of digital input 2 IN-TM O/C-2 NO NO NO
Type of digital input 3 IN-TM O/C-3 NO NO NO
Type of digital input 4 IN-TM O/C-4 NO NO NO
F-34
Type of digital input 5
IN-TM O/C-5 NO
NO NO
Function of digital output 11
OUT-TM 1 FA1 FA1 FA1
Function of digital output 12 OUT-TM 2 RUN RUN RUN
Type of alarm relay output
OUT-TM O/C-A NC
NC NC
Digital output 11 type OUT-TM O/C-1 NC NC NC
F-35
Digital output 12 type OUT-TM O/C-2 NC NC NC
F-36 Carrier frequency CARRIER 12.0kHz 2 or 5kHz 2 or 5kHz
F-37 Function of FM terminal
MONITOR A-F
A-F A-F
National version INIT SEL EUR EUR USA
Motor direction INIT DOPE FWD FWD FWD
F-38
Initializing mode INIT MODE TRP TRP
PID control active / not active
PID SW OFF
OFF OFF
P (proportional) gain of PID control PID P 1.0 1.0 1.0
I (integral) gain of PID control PID I 001.0 1.0 1.0
D (differential) gain of PID control PID D 000.0 0.0 0.0
Scale conversion of PID control
PID CONV 01.00
1.00 1.00
F-43
Feedback signal location PID INPT CUR CUR CUR