Hillrom Welch Allyn Connex ProBP 3400 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 64

Hillrom Welch Allyn Connex ProBP 3400 Скачать руководство пользователя страница 34

•

Battery

•

Rear housing

1. Unlock the ZIF connector (J5) on the main board by sliding the latching piece of the connector

away from the connector body.

CAUTION

Do not use excessive force when releasing pressure on

the connector. Excessive force may result in breaking the sliding
outer piece.

2. Remove the flex cable from the ZIF connector.

3. Grasp both side panels and lift them and the chassis and circuit board assemblies away from

the front housing.

4. While holding the chassis and circuit board assemblies, remove the side panels.

CAUTION

Always protect the LCD. When the main board is outside of the device

case, never rest the board on the LCD.

When replacing the front housing

Remove the liner from the inside of the housing window if present. Wipe any dust or fingerprints
off of the window with a clean cloth.

Reassembly notes

Before reassembly, do the following to ensure proper installation of the side panels and isolation
bumpers:

1. Place the front housing and side panels on the antistatic mat as shown in the diagram below,

making sure that the arrows on the side panels point away from the front housing.

30 Disassembly and repair

Welch Allyn® Connex® ProBP™ 3400 digital blood pressure device

«
...
32
33
34
35
36
...
»

Содержание Welch Allyn Connex ProBP 3400

































































Отзывы:

Нет отзывов