Hillrom Welch Allyn Connex ProBP 3400 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 64

Hillrom Welch Allyn Connex ProBP 3400 Скачать руководство пользователя страница 17

Component

Service interval

Service procedure

Device

Annually

Calibration check using the Silver-level

Welch Allyn Service Tool

Use the Gold-level Welch Allyn Service Tool to perform a complete functional verification and
calibration of the device whenever any of the following conditions exist:
•

Based on the calibration check, the device does not meet specifications

•

The device has been dropped or otherwise damaged

•

The device is malfunctioning

•

The case has been opened

•

A part has been replaced

For details on performing the functional verification, see the section on functional verification.

Maintenance

For device maintenance information, see the directions for use. Covered topics include the
following:
•

Changing the battery

•

Inspecting and cleaning the device and accessories

Configuration options

The device is available in the configurations shown in the table below. The model-number suffix,
denoted by an asterisk (*), indicates the power cord packaged with the device. Available suffixes are
listed after the configuration table.

NOTE

For more configuration options, including approved accessories, see the

directions for use.

Model

Standard BP

SureBP

Bluetooth

Mounting

configuration

34BFHT-*

Handheld

34BFWT-*

Wall mounted

34BFST-*

Mobile stand

34XFHT-*

Handheld

34XFWT-*

Wall mounted

34XFST-*

Mobile stand

34BXHT-*

Handheld

Service Manual

Overview 13

«
...
15
16
17
18
19
...
»

Содержание Welch Allyn Connex ProBP 3400

































































Отзывы:

Нет отзывов