HIKVISION DS-K5604A-3XF/V Скачать руководство пользователя

Страница: 18 / 136

Chapter 3 Installation

3.1 Installation Environment

• Avoid backlight, direct sunlight, and indirect sunlight.

• For better face recognition, there should be light source in or near the installation environment.

• Sunlight, wind, hot/cool air from air conditioner and other external factors, which may affect

surface temperature, will create the deviation of the temperature measurement. In order to get

an accurate result, make sure the device is applied indoors and windlessly (where is relatively

isolated from the outdoors). The working temperature should keep between 10 °C and 35 °C. If

there are no suitable environments for temperature measurement (the area faces the indoor

and connects the outdoor, the area at the door of the indoor environment, etc.), building a

temporary temperature measurement environment is suggested.

• Influence Factors of Temperature Measurement:

Wind: The wind will take the heat away, which may affect the measurement result.

Sweat: The sweat will take the heat away, which may affect the measurement result.

Air Conditioner (Cool Air): If the indoor temperature is low, the surface temperature may also

lower than the actual temperature, which may affect the measurement result.

Air Conditioner (Heat) or Heating: If the indoor temperature is high, the surface temperature

may also higher than the actual temperature, which may affect the measurement result.

• In order to make the device work properly, you should wait for 90 min after the device is

powered on.

• For details about installation environment, see Tips for Installation Environment .

3.2 Install Device

Before You Start

Make sure the ground surface has drilled holes for device installation.
Steps

1. Remove the two bottom screws (2-SC-KM3×5B-JMF) on both sides of the bottom cover.

2. Remove the bottom cover.

3. Align the device with the drilled holes on the ground and insert 3 supplied expansion bolts

(M6×65). Make sure the expansion bolts are higher than the ground.

4. Secure the expansion bolts with nuts.

5. Align the device with the mounting plate and hang the device on the mounting plate.

6. Install the bottom cover back on the device with 2 bottom screws.

DS-K5604A-3XF Series Face Recognition Terminal User Manual

Содержание DS-K5604A-3XF/V









































































































































Результаты поиска

Содержание DS-K5604A-3XF/V

Отзывы:

Похожие инструкции для DS-K5604A-3XF/V

Бренды по названию

Популярные бренды

HIKVISION DS-K5604A-3XF/V, Руководство пользователя

Результаты поиска

Содержание DS-K5604A-3XF/V

Отзывы:

Похожие инструкции для DS-K5604A-3XF/V

Бренды по названию

Популярные бренды