HIKVISION DS-8100-ST Series Скачать руководство пользователя страница 13

Страница: 13 / 121

Operating Your DVR

There are numerous ways to navigate and operate your DVR. You may use the

Front Panel Controls,

the included

(Infrared) Remote

, a

Mouse

and the

Soft Keyboard

Using the Front Panel Controls

Figure 5. DS-8100HCI-ST DVR Front Panel

The controls on the front panel include:

Power Button:

Powers DVR on/off.

IR Receiver:

Receiver for IR remote.

USB Ports:

Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB

Hard Disk Drive (HDD).

Status Indicators:

Status indicators for different features of the DVR.

•

Alarm:

Alarm indicator turns red when a sensor alarm is detected.

•

Ready:

Ready indicator turns blue when DVR is functioning properly.

•

Status:

Status indicator turns blue when DVR is controlled by an IR remote. Indicator turns red when

controlled by a keyboard and purple when IR remote and keyboard is used at the same time.

•

HDD:

HDD indicator blinks red when data is being read from or written to HDD.

•

Modem:

Reserved.

•

TX/RX:

TX/RX indictor blinks blue when network connection is functioning properly.

•

Guard:

Guard indicator turns blue when the device is armed, off when the device is unarmed. The

arm/disarm state can be initiated by pressing and holding on the ESC button for more than 3 seconds
in Preview mode.

Alphanumeric Buttons:

Alphanumeric buttons used in various menus of the DVR. Some uses include:

•

Switching to the corresponding channel in Preview or PTZ Control mode.

•

Inputting numbers and characters in Edit mode.

•

Switching between different channels in Playback mode.

Control Buttons:

•

ESC Button:

The ESC button is used to escape to the previous menu and to arm/disarm the DVR in

Preview mode.

•

REC/SHOT Button:

The REC/SHOT button is used to enter the Manual Record interface. If used

when controlling a PTZ, pressing the REC/SHOT button and then a Numeric button will call a PTZ
preset.

•

PLAY/AUTO Button:

The PLAY/AUTO button is used to enter the Playback menu. It is also used

to turn audio on/off in the Playback menu and auto scan in the PTZ Control menu.

•

ZOOM+ Button:

The ZOOM+ button is used to zoom the PTZ camera in when in the PTZ Control

menu.

Содержание DS-8100-ST Series


























































































































Результаты поиска

Содержание DS-8100-ST Series

Отзывы:

Похожие инструкции для DS-8100-ST Series

Бренды по названию

Популярные бренды

HIKVISION DS-8100-ST Series, Руководство пользователя

Результаты поиска

Содержание DS-8100-ST Series

Отзывы:

Похожие инструкции для DS-8100-ST Series

Бренды по названию

Популярные бренды