Henny Penny PFE-591 Скачать руководство пользователя

Страница: 58 / 73

Model PFE- 591

3-16. SPECIAL PROGRAM

Manager Code Change (SP-15)

MODE (Continued)

This allows the operator to change the program code, or manager
code (factory set at 1, 2, 3) used to access Product
Programming, Special Programming, Clock Set, Data Comm,
and Heat Control Modes.

a. Follows steps 1 and 2 above.

b.Press until “SP-15” and “CHANGE, MGR CODE?

1=YES” shows in display, along with “CODE”.

c. Press . “ENTER NEW CODE, P=DONE, I=QUIT”

shows in display. Press Product buttons with new code.

d.If satisfied with code, press . “REPEAT NEW

CODE, P=DONE, I=QUIT, shows in display. Press same
code buttons in step c.

e. If satisfied with code, press . *CODE CHANGE*

shows in display.

f. If not satisfied with code, press and “*CANCELLED*”

shows in display, then reverts back to “SP-15” and
“CHANGE, MGR CODE, 1=YES”. Then the above steps
can be repeated.

Usage Code Change (SP-16)

This allows the operator to change the usage code(factory set at
1, 2, 3) used to reset the usage data in the Information Mode.

a. Follows steps 1 and 2 above.

b.Press until “SP-16” and “CHANGE, USG CODE?

1=YES” shows in display, along with “CODE”.

c. Press . “ENTER NEW CODE, P=DONE, I=QUIT”

shows in display. Press Product buttons with new code.

d.If satisfied with code, press . “REPEAT NEW

CODE, P=DONE, I=QUIT, shows in display. Press same
code buttons in step c.

e. If satisfied with code, press . “*CODE CHANGE*”

shows in display.

f. If not satisfied with code, press and “*CANCELLED*”

shows in display, then reverts back to “SP-16” and
“CHANGE, USG CODE, 1=YES”. Then the above steps
can be repeated.

3-42

403

Содержание PFE-591










































































Результаты поиска

Содержание PFE-591

Отзывы:

Похожие инструкции для PFE-591

Бренды по названию

Популярные бренды

Henny Penny PFE-591, Руководство оператора

Результаты поиска

Содержание PFE-591

Отзывы:

Похожие инструкции для PFE-591

Бренды по названию

Популярные бренды