manualshive.com logo in svg

Henny Penny PFE-591, Руководство оператора

Поделиться
Скачать
Henny Penny PFE-591 Скачать руководство пользователя страница 53

           Model PFE- 591

Type of shortening to be melted - Liquid or Solid (SP-6)

The Melt Cycle can be set to the type of shortening being used.

a. Follow steps 1 and 2 above.

b. Press and release           5 times.  “SP-6”

and “MELT CYCLE SELECT” flashes on the display,
along with “l=LIQ” or “2=SOLID”.

c. Press

  to toggle from one type to another.

The type of shortening being used in the cooker
determines the amount of heat applied during the Melt
Cycle.  If the controls are set to the solid setting, less heat
is applied to the shortening, than if the controls were set
to liquid.  Too much heat applied to solid shortening
causes much smoking, and could cause a fire.  Match this
setting to the type of shortening being used at the time.

When using solid shortening, it is recommended to melt
the shortening on an outside source before placing
shortening in the frypot.  Unless elements are
completely covered in shortening, fire or damage to the
frypot could result.

Idle Mode (SP-7)

A programmed Idle Mode allows the shortening temperature to
drop to a lower temperature when not in use.  This saves on the
shortening and utilities.
 a. Follow steps 1and 2 above.

 b. Press and release

  6 times.  “SP-7” and “IDLE

MODE ENABLED?” flashes in the display, along with
“NO” or “YES”.

 c. Press and release

to toggle from NO to YES,

or vice versa.

 

d. With “YES” in the display, the Idle Mode is enabled.

Press and release            .  “SP-7A” and
“IDLE SETPT TEMP” shows in the display, along with
the preset temperature.

3-16.    SPECIAL PROGRAM

  MODE (Continued)

403

     3-37

Содержание PFE-591










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды