Hardi MUSTANG 3500 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 68

background image

14

HARDI

®

MUSTANG 3500 OPERATOR’S MANUAL

AUTO/MAN/HOLD SWITCH or MASTER SWITCH

This MASTER switch will change the control status of the system from
fully automatic control (“AUTO”), manual control (“MAN”), or HOLD.

During normal operation, when the MASTER switch is in AUTO, the
console adjusts the regulating valve to maintain the desired application
rate. For example, as speed increases, pressure will increase
automatically in order to maintain the desired application rate. As speed
decreases, pressure decreases.

During normal operation, when the MASTER switch is in MAN, the
application rate will not be maintained by the console automatically.
Using the ADJUST switch while in MAN allows the operator to increase
or decrease the flow or pressure manually as needed.

During normal operation, when the MASTER switch is in HOLD, all
section valves are turned off, (spraying will stop) and area, distance and
flow will stop accumulating and foam marker will stop. For example, when
turning on end rows, place the MASTER switch in HOLD.

RESET BUTTON

The RESET button is used to clear a selected counter. To do this, simply
turn the rotary dial to any of the counter positions (Total Area, Field Area,
Total Flow, Field Flow, or Distance), and press and hold the reset button
for one second.

IMPORTANT:

when clearing field area, field flow is

cleared as well. The same holds true for total area and total flow.

MODE SWITCH (TWIN FORCE CONSOLE ONLY)

TWIN FORCE SWITCH:

RPM Position – In this position, fan speed can be adjusted. To do
this, place the switch in the RPM position, and use the “adjust”
switch to increase or decrease the fan speed. The console will not
allow fan speed greater than 3200
RPM.The console will show “fan RPM”
in the lower right while in this mode, and
RPM will be displayed in the upper half
of display indicating the mode the user
is in. If the PTO is disengaged and
hydraulic flow to the Fan motor stops, causing Fan RPM to read 0,
the system will automatically take the hydraulic pump output to the
lowest setting.

9

10

8

«
...
15
16
17
18
19
...
»

Содержание MUSTANG 3500





































































Отзывы:

Нет отзывов

Похожие инструкции для MUSTANG 3500

Бренд: WAGNER Страницы: 88

Бренд: Binks Страницы: 4

Бренд: Parkside Страницы: 24

Бренд: Samoa Страницы: 28

Бренд: Labnet Страницы: 7

Бренд: jobmate Страницы: 9

Pakblast 50 Gal

Бренд: Rears Страницы: 58

Бренд: BGS technic Страницы: 3

Бренд: Fimco Страницы: 14

Бренд: Fimco Страницы: 12

Бренд: Fimco Страницы: 12

Бренд: Fimco Страницы: 14

WoodPerfect W 600

Бренд: WAGNER Страницы: 52

WallPerfect W 615 I-Spray

Бренд: WAGNER Страницы: 74

Бренд: Duraline Systems Страницы: 28

Бренд: Meganex Страницы: 13

Бренд: Hardi Страницы: 166

Бренд: PA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды