Hardi MUSTANG 3500 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 68

background image

15

HARDI

®

MUSTANG 3500 OPERATOR’S MANUAL

ANGLE Position – This position is used to
adjust the slot angle. To do this, place the
switch in the ANGLE position, and use the
“adjust” switch to increase or decrease the
slot angle.

There are 3 modes of operation for the Slot Angle feature on the HARDI

®

Mustang 3500: Manual, Preset and Auto.

WHEN ENTERING THE SLOT ANGLE
MODE:

if the user places the Mode Switch in

the Angle position, the top half of the LCD
reads AnglE and either RATE 1, 2, or 3. The
lower left reads a number between .0 and
12.0 and the lower right display reads either Auto or PrSEt (preset).

MANUAL MODE:

To operate the Slot Angle manually, simply place the

Mode Switch in ANGLE and the Rotary Switch in any green (operational)
position, using the Adjust Switch, manually change the Slot Angle to the
desired position.

PRESET MODE:

To operate the Slot Angle in the Preset Mode, toggle

the MODE SWITCH to the ANGLE position and the ROTARY SWITCH
to any green position (the lower right area of the display must read
PrSET).

•

If the RATE 1, 2 or 3 button is pressed, the Slot Angle will transition

to the associated preset value. The value in lower left display represents
the time in seconds the Slot Angle actuators will run from the zero point.
If the value in RATE 1 is set to 2.5 and the Rate 1 button is pressed, the
Slot Angle will run forward for 12 seconds and then rearward for 2.5
seconds.

•

If the value in Rate 2 is set to 4.7 and the RATE 2 button is pressed,

the Slot angle will run forward for 12 seconds and then rearward for 4.7
seconds.

•

If the value in Rate 3 is set to 6.2 and the RATE 3 button is pressed,

the Slot Angle will run forward for 12 seconds and then rearward for 6.2
seconds. To adjust the preset value the Mode Switch must be in the
ANGLE position, the Master Switch in HOLD and the Rotary Switch in
any calibration (red) position, to adjust, select the associated RATE
button and adjust the value using the Adjust Switch.

meters

inches

ERROR

2

N / Ac

liters / ha

Rate 1

«
...
16
17
18
19
20
...
»

Содержание MUSTANG 3500





































































Отзывы:

Нет отзывов

Похожие инструкции для MUSTANG 3500

Бренд: Electro Spray Страницы: 16

Бренд: FAXXWERK Страницы: 16

Бренд: Forch Страницы: 44

Бренд: B&G Страницы: 2

Бренд: Vito Agro Страницы: 8

Бренд: SATA Страницы: 130

sataminijet 4400 B

Бренд: SATA Страницы: 452

Бренд: Clarke Страницы: 16

Бренд: Hardi Страницы: 56

Бренд: Hardi Страницы: 76

Бренд: Hardi Страницы: 104

Бренд: Power Fist Страницы: 20

Бренд: Power Fist Страницы: 24

Бренд: Graco Страницы: 70

Бренд: Graco Страницы: 78

Бренд: Air Gunsa Страницы: 8

Бренд: Graco Страницы: 44

Speedy Sprayer 331-A

Бренд: W.R. BROWN Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды