Hardi MUSTANG 3500 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 68

background image

59

HARDI MT-9000 OPERATOR’S MANUAL

from the external PC's prescribed rate, there are two methods to override
VRA mode, either Manual override or Automatic override.
Note that while in any form of "override" the console will continue to rreceive
and store any new VRA Targets sent by the PC, but it will not use them until
the user decides to re-enter VRA mode in which case the console will
immediately be synchronized with the external PC and its currently
prescribed application rate.

MANUAL OVERRIDE:

If the Master switch is moved to "MAN" the user can override the current
prescribed VRA target rate by using the adjust switch to make the necessary
adjustment to the application rate.
The user can also override a VRA "Hold" condition in a similar manner. The
external VRA program places the console in Hold by send a Target of "0",
which stops the sprayer. If the user sets the Master switch to "Man", it
overrides the PC "Hold" condition (console displays "Phold") turning the
sprayer back on and allowing the user to adjust the rate manually using the
INC/DEC switch.
To return to VRA mode, move the Master switch back to "AUTO". The
console display shows the current status prescribed by the PC, either a VRA
application rate or "Phold".

AUTOMATIC OVERRIDE:

Pressing either the Rate 2 or Rate 3 key will override VRA mode, and
instead allows the use of two alternative rates that still operate under
automatic control.

Note the differences when in Automatic Override mode:
• The "Rate" icon is now followed by a "2" or "3" which indicates the

VRA mode is not active (overridden).

• The top display will shown any new user selected Target for 2

seconds (same as in normal operation).

• The Adjust switch functions as normal, to increase or decrease

Target 2 or 3 by the "AdjustRate" amount.

If the user presses the Rate 1 key the console will reactivate VRA mode and
resume using the external PC's prescribed rate.

«
...
60
61
62
63
64
...
»

Содержание MUSTANG 3500





































































Отзывы:

Нет отзывов

Похожие инструкции для MUSTANG 3500

Бренд: paasche Страницы: 4

Бренд: Electro Spray Страницы: 16

Бренд: Graco Страницы: 16

Бренд: Campbell Hausfeld Страницы: 4

Бренд: Fimco Страницы: 12

JGP-503 CONVENTIONAL

Бренд: DeVilbiss Страницы: 6

Бренд: DeVilbiss Страницы: 8

Бренд: Hardi Страницы: 122

Бренд: ES manufacturing Страницы: 6

Бренд: Intex Страницы: 5

Бренд: C.A. Technologies Страницы: 4

Бренд: Binks Страницы: 20

Бренд: Sunex Tools Страницы: 8

Бренд: Sunex Tools Страницы: 22

Spray Station HV5500

Бренд: Earlex Страницы: 36

Бренд: DaytonAudio Страницы: 4

Бренд: WAGNER Страницы: 144

Бренд: Toyama Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды