Hardi MUSTANG 3500 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 68

background image

44

HARDI

®

MUSTANG 3500 OPERATOR’S MANUAL

CAN’T GET THERE? If you can’t get to the desired application rate, a
problem may exist with the pump, nozzles or other plumbing
components. Please refer to your Sprayer Manual.

Now is a good time to confirm that GPA, GPM, MPH, WIDTH and PSI
all coincide with the nozzle manufacturer’s charts. PSI may be slightly
higher than indicated by the charts due to pressure drop across the
plumbing valve, nozzle diaphragm check valve, nozzle screens, etc…

5. With the master switch in HOLD, turn the rotary dial back to the

SPEED position. Use the ADJUST switch to enter minimum
application speed. (Remember, the minimum application speed is
normally not less than half of the maximum application speed.)

6. Put the master switch in “MAN” control mode; turn all active

boom switches ON.

7. Turn the rotary dial to the FLOW PER MINUTE position and hold

ADJUST

switch in the "–" position until application rate stops

decreasing. The display should now read less than the desired
application rate.

It is not normally a problem if the application rate goes all the way to
zero when holding the “–” switch, as long as it goes back up when the
“+” switch is held.

CAN’T GET THERE? If holding the “–” switch does not get the
application rate to go below the target application rate, please refer to
your Sprayer Manual.

8. Put the master switch in HOLD and turn the rotary dial to the

SPEED position. Use the ADJUST switch to enter target application
speed.

9. Put the master switch in AUTO and turn the rotary dial to any of the

upper six operating positions except SPEED. The console should
take control and lock on to your calibrated target rate.

If you calibrated your ADJUST RATE to zero (.0), disregard steps 10
and 11.

«
...
45
46
47
48
49
...
»

Содержание MUSTANG 3500





































































Отзывы:

Нет отзывов

Похожие инструкции для MUSTANG 3500

Бренд: Vector Fog Страницы: 15

Super Finish 23 Select

Бренд: WAGNER Страницы: 36

HOME STUDIO SPRAYER

Бренд: WAGNER Страницы: 8

Бренд: Uni-ram Страницы: 14

Verti-Spray 6000

Бренд: Redexim Страницы: 10

12 VOLT SPOT SPRAYER

Бренд: Master MFG Страницы: 12

Бренд: Raider Страницы: 80

Бренд: Flowzone Страницы: 14

SUNJOE SJ-APS-2G-RM

Бренд: SNOWJOE Страницы: 16

Sunjoe 24V-GS-LTW-RM

Бренд: SNOWJOE Страницы: 20

POWERJOE 24V-PS1-RM

Бренд: SNOWJOE Страницы: 24

HVLP SmartFinish

Бренд: Storch Страницы: 148

Бренд: Titan Страницы: 20

Бренд: Tritech Страницы: 12

Бренд: Harbor Freight Tools Страницы: 5

Бренд: Harbor Freight Tools Страницы: 8

Бренд: Hobbico Страницы: 2

Бренд: MATABI Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды