Haier GE PTW600BPR DG Series Скачать руководство пользователя страница 46

Страница: 46 / 77

– 46 –

Drive Belt Motor:

For the PTW600/605 control

board. The connector for the speed sensor is:

J701 5 VDC. Pin 3 is ground. Pin 2 is the hall

effect sensor. The speed/hall sensor can be

diagnosed in two different ways.

1. Run Service Mode Test 14: Spin Test.

If the speed/hall sensor is bad or disconnected,

the basket will start to spin normally at first. After

5-seconds, motor power will be stopped.

If the washer continues to spin for at least

15-seconds, the speed/hall sensor is good.

2. With the wiring connectors connected to the

main board and to the speed sensor, test for

proper voltage.

At connector J710, between pins 1 and 3

resistance should be +/- 5 volts with speed

sensor harness side connector either plugged or

unplugged into J710.

Speed/Hall Sensor Removal

1. Remove belt protector and belt (see

Belt

Removal

under

Drive Belt

in this section

of the service guide), and remove the drive

pulley, transmission pulley, and the pully (see

Drive/Transmission Pulleys

in this section of

the service guide).

2. Disconnect the speed/hall sensor from the

drive motor and disconnect from the main

harness.

Speed/Hall Sensor

The speed/hall sensor is mounted to the drive

motor and sends a pulse signal back to the

control board. This is done when the magnet that

is mounted in the drive motor pulley pass over the

sensor.

If the control does not read any signal from the

sensor from the movement of the motor, the

washer cycle will stop.

Speed/Hall Sensor Diagnosing
Direct Drive Motor:

For the

PTW700/705/900/905 control board. The

connector for the speed sensor is: J1101. Pin 1

is 15 VDC, Pin 4 is ground. Pin 3 is the hall effect

sensor. Pin 2 is the PTC input.

Magnet

(

Continued next page

)

5
6
7
8

1
2
3
4

1 2 3 4

Hamess

Side

Mate

J1101

(GREEN)

PTC HALL

22 - BX

22 - VX

22 - YX

22 - RX

1 2 3

HE SPEED SENSOR

SPEED

SENSOR

- 5V

SIGNAL

GND

J701

(YELLOW)

22 - CX
22 - NX
22 - OX

Pulley Removal

1. Remove the two hex-head nuts (one for

each pulley) securing them to the motor and

transmission shafts.

Slide the pulleys off the motor and

transmission shafts. Torque new pulley nut to

110-in. pounds. when reinstalling.

Guide

Post

Hole

Содержание GE PTW600BPR DG Series














































































Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды

Haier GE PTW600BPR DG Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды