manualshive.com logo in svg

Haier GE PTW600BPR DG Series, Техническое обслуживание руководство, Страница: 40 / 77

Поделиться
Скачать
Haier GE PTW600BPR DG Series Скачать руководство пользователя страница 40

– 40 –

The basket assembly consists of the balance 

ring, basket side wall and the basket bottom.  The 

hub is molded into the basket bottom.

Basket Removal

1.  Remove backsplash assembly (see 

Backsplash Removal

 under 

Control Panel 

Housing / Backsplash

 in the 

Cabinet and 

Structure 

section of this guide), remove 

top cover and suspension assembly (see 

Top Cover Removal

 under 

Top Cover

 and 

Suspension Assembly Removal

 under 

Suspension Assembly

 in the 

Capacitor 

(For 600/605 Models Only)

 section of this 

service guide).

2.  Remove the tub cover by unclasping eight 

clips around the edge and lift off.

3.  Remove the hub nut (1 5/16-inch.) and 

conical washer.  The hub nut is reverse 

threads.  It will need to be turned to the right 

to loosen. 

4.  Lift the basket out from the tub.  The basket 

assembly weight is approximately 21-pounds.

A torque limiter (Part #: WX05X10028) should be 

used when removing or installing the hub nut with 

an impact gun.

  

Basket Assembly

  Water Levels

Approximate Minimum Water Levels

• 

Impeller

: 10-gallons or 4.1-in. deep from the 

bottom of the basket.

• 

Agitator

: 8-gallons or 4.85-in. deep from the 

bottom of the basket.

Approximate Maximum Water Levels

• 

Impeller

: 38-gallons or 17.4-in. deep from 

the bottom of the basket.  Press and hold the 

Deep Fill button for 3-seconds to achieve.

•  Impeller Bulky setting water level is 

38-gallons or 16.7-in. deep from the bottom of 

the basket.

• 

Agitator Models

: 36-gallons or 16.5-in. depth 

from the bottom of the basket set to super.

NOTE

: These levels are measured starting from 

an empty basket.

Clips

Содержание GE PTW600BPR DG Series














































































Отзывы:

Нет отзывов