Haier GE PTW600BPR DG Series Скачать руководство пользователя страница 51

Страница: 51 / 77

– 51 –

4. Cut the wire ties that support the main

harness to the platform assembly.

5. Remove hex-head bolts securing the motor

shield and the harness brackets to the

platform.

6. Cut the wire ties that support the main

harness to the platform assembly.

7. Remove hex-head bolts securing the motor

shield and the harness brackets to the

platform.

8. Remove eight hex-head bolts securing the

platform to the bottom of the tub.

9. Pry platform assembly away from the tub.

NOTE

: The tub seal is pressed onto the shaft.

Prying against the tub bottom to remove the

platform assembly may be necessary.

Platform/Transmission Assembly

The platform assembly not only houses the

transmission but is also used to mount the drive

motor and mode shifter. The transmission has

planetary gears inside to assist with the agitation

and spin cycles of the washer. It is one complete

part with the exception of the two harness

mounting brackets (some models have one

harness mounting bracket) and a motor splash

guard.

Platform/Transmission Removal

1. Remove belt protector (see

Belt Protector

Removal

under

Drive Belt

in this section of

the service guide). Remove the drive belt

motor (for 600/605 models, see

Drive Belt

Motor Removal

under

Drive Belt Motor

this section of the service guide), remove

direct drive motor (for 700/705 and 900/905

models, see

Direct Drive Motor Removal

under

Direct Drive Motor

in this section of

the service guide), remove mode shifter (see

Direct Drive Mode Shifter Removal

under

Mode Shifter

, and for direct drive models and

drive belt mode shifter removal, see

Drive

Belt Mode Shifter Removal

under

Mode

Shifter

in this section of the service guide),

remove the impeller or agitator (see

Impeller

Removal

Agitator Removal

under

Agitators

in the

Fill System

section).

2. Remove the hub nut and Belleville washer.

The hub nut is reverse threads. It needs to be

turned clockwise (CW) to loosen.

3. Lean washer back or lay on its side to access

the bottom of the washer.

For direct dive models, remove direct drive motor

(see

Direct Drive Motor Removal

, under

Direct

Drive Motor

in this section). Remove the speed

sensor (see

Speed/Hall Sensor Removal

, under

Speed/Hall Sensor

in this section). Remove the

mode shifter (see

Mode Shifter

section).

For drive belt models, remove belt protector

and belt (see

Belt Protector Removal and

Belt Removal

under

Drive Belt

in this section).

Remove drive/transmission pulleys (see

Drive/

Transmission Pulleys

in this section). Remove

the speed sensor (see

Speed/Hall Sensor

Removal

, under

Speed/Hall Sensor

in this

section). Remove the mode shifter (see

Mode

Shifter

in this section of the guide).

(

Continued next page

)

Содержание GE PTW600BPR DG Series














































































Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды

Haier GE PTW600BPR DG Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды