manualshive.com logo in svg

Haier GE PTW600BPR DG Series, Техническое обслуживание руководство, Страница: 49 / 77

Поделиться
Скачать
Haier GE PTW600BPR DG Series Скачать руководство пользователя страница 49

– 49 –

The mode shifter consists of a motor that 

operates by receiving 120 VAC from the control 

board, a micro switch, and a spring and clutch. 

It engages or disengages the clutch with the 

transmission pulley, depending on whether the 

cycle is in spin or agitate.

Mode Shifter Motor 

Diagnosing

From the J512 (for 700/705 and 900/905 

models), J401 (for 600/605 model connector 

on the main board, the 

brown

 wire pin 1 to the 

grey

 wire pin 4 should read approximately 5,700-

ohms.  Run Service Mode Test 14: Spin Test and 

Test 15: Agitate Test to manually check mode 

shifter operation.

Drive Belt Mode Shifter Removal 

1.  Remove belt protector and belt (see 

Drive 

Belt

 in this section of the service guide). 

2.  Remove the drive/transmission pulleys (see 

Drive/Transmission Pulleys

 is this section 

of the service guide).

3.  Remove the speed/hall sensor (see 

Speed/

Hall Sensor Removal

 under 

Speed/Hall 

Sensor

 in this section of the service guide).

4.  Disconnect the mode shifter motor harness 

connector.

5.  Remove two hex-head bolts securing the 

mode shifter to the platform. The mode shifter, 

clutch, clutch spring, and flat washer will pull 

away from the platform.

Direct Drive Mode Shifter Removal

1.  Remove direct drive motor (see 

Direct Drive 

Motor Removal

 under 

Direct Drive Motor

 in 

this section of the service guide).

2.  Disconnect the mode shifter motor harness 

connector.

3.  Remove two 3/8-in. hex-head bolts securing 

the mode shifter to the platform.  The mode 

shifter, clutch, clutch spring, and flat washer 

will pull away from the platform.

Mode Shifter Switch 

Diagnosing

Normally, the mode shifter switch is closed and 

ready for the spin cycle.  When agitating, the 

switch should be open.  From the J512 (for 

700/705 and 900/905 models) J401 (for 600/605 

model), check for continuity (approximately 

0-ohms) on the main board pin 5 (

tan

 wire TX) to 

pin 3 (

grey

 wire SX).

Reinstalling Drive Belt Mode Shifter

1. 

Install the flat washer onto the lower 

transmission shaft.

2.  Install the clutch spring.

3.  Slide the clutch into the clutch level of the 

mode shifter and slide the clutch onto the 

shaft.  There are guide pins on the bottom of 

the mode shifter that go into locator holes on 

the platform.

(

Continued next page

)

Mode 

Shifter

  Mode Shifter 

Содержание GE PTW600BPR DG Series














































































Отзывы:

Нет отзывов