Haier GE PTW600BPR DG Series Скачать руководство пользователя страница 32

Страница: 32 / 77

– 32 –

4. Slide the harness grommet out toward the

rear of the washer. Disengage the power

cord from the top cover by lifting the front part

of the cord and then slide forward to remove.

5. Remove two hex-head screws holding top

cover to cabinet assembly.

6. Raise the rear of the top cover up and pull

forward slightly to disengage the front clips

using putty-knife.

Top Cover

Top Cover Removal

1. Remove backsplash assembly (see

Backsplash Removal

under

Control Panel

Housing / Backsplash Assembly

) and

remove the main board (see

Main Board

Housing Removal

under

Main Board

) both

found in the

Cabinet and Structure

section

of this service guide).

2. Remove the lid assembly (see

Lid Assembly

Removal

under

Lid Assembly

in the

Capacitor (For 600/605 Models Only)

section of this service guide).

3. Remove two hex-head ground screws.

Dampers

Lid Hinge

Ground Screws

Harness

Grommet

Power

Cord

Screws

Top Cover

Assembly

Front

Clips

Screws

5. Remove two damper assemblies and lid hinge

from lid assembly.

Содержание GE PTW600BPR DG Series














































































Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды

Haier GE PTW600BPR DG Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды