Hach ORBISPHERE K-M1100 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 116

background image

19

Section 3

Installation

This section provides necessary information to install and connect the analyzer. The installation
of the analyzer should be performed in accordance with relevant local regulations.

3.1 Unpacking

Remove carefully the instrument and its accessories from the box and packing material,
referring to the packing list included to confirm that everything has been delivered.

Please visually inspect the instrument for shipping damage. If anything is missing or damaged,
contact the manufacturer or your dealer immediately.

You may want to retain the box and other packing material in case later you need to ship the
instrument. Refer to

Storage, handling and transportation on page 103

. Please dispose safely

and ecologically of the box and packing material (if not stored for future use).

Please read through this manual thoroughly before carrying out the installation.

D A N G E R

Electrocution Hazard. Do not connect AC power to a 5 VDC powered model.

WA R N I N G

Potential Electrocution Hazard. Always disconnect power to the instrument when
making electrical connections.

WA R N I N G

Potential Electrocution Hazard. If this equipment is used outdoors or in potentially
wet locations a

Ground Fault Interrupt

device must be used for connecting the

equipment to its main power source.

WA R N I N G

Potential Electrocution Hazard. A protective earth (PE) ground connection is
required for both 100-240 VAC and 5 VDC wiring applications. Failure to connect a
good PE ground connection can result in shock hazards and poor performance due
to electromagnetic interferences. ALWAYS connect a good PE ground to the
controller terminal.

C A U T I O N

Personal Injury Hazard. Only qualified personnel should conduct the tasks described in this
section of the manual.

N O T I C E

Install the device in a location and position that gives easy access to the disconnect device
and its operation.

N O T I C E

Potential Instrument Damage. Delicate internal electronic components can be
damaged by static electricity, resulting in degraded performance or eventual failure.

«
...
18
19
20
21
22
...
»

Содержание ORBISPHERE K-M1100





















































































































Отзывы:

Нет отзывов

Похожие инструкции для ORBISPHERE K-M1100

scx-4100 series

Бренд: Samsung Страницы: 8

Бренд: DataCard Страницы: 2

Бренд: DataCard Страницы: 24

ImageCard series

Бренд: DataCard Страницы: 2

ImageCard series

Бренд: DataCard Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Feniex Страницы: 6

Бренд: Fencing SmartBox Страницы: 11

Бренд: Feiyu Страницы: 4

Бренд: FAZUA Страницы: 84

Бренд: GAI-Tronics Страницы: 22

Бренд: FeiYu Tech Страницы: 34

Бренд: Garmin Страницы: 26

Бренд: Garmin Страницы: 8

Бренд: Garmin Страницы: 72

Бренд: oliser Страницы: 6

Бренд: T-up Страницы: 14

Бренд: Salta Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды