Hach ORBISPHERE K-M1100 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 116

background image

11

Section 2

Specifications

2.1 Sensor descriptions

ORBISPHERE K1100 sensor

The high accuracy K1100 sensor is a luminescent sensor measuring dissolved oxygen, and has
been optimized specifically for measurements in water processes in the power industry.

ORBISPHERE M1100 sensor

The high accuracy M1100 sensor is a luminescent sensor measuring dissolved oxygen, and has
been optimized specifically for measurements in beer processes in the beverage industry.

2.2 Technical data

Controller

Enclosure ratings

IP 65
Totally protected against dust.
Protected against low pressure jets of water from all directions.

NEMA4X (wall mount only)
Totally protected against dust.
Protected against pressure jets of water from all directions.

WA R N I N G

Enclosure rating does not apply to external power supply for benchtop
instruments.

Certifications

CE compliance:

EMC Directive, LVD Directive

Safety rating

ETL, conforming to UL 61010-1 and
CSA 22.2 No. 61010-1

Analog current output version on
the measurement board

4-20 mA (default) or 0-20 mA (configuration with software)
3 configurable outputs
Maximum load: 500 ohm
Sensitivity: 20µA
Accuracy: ± 0.5% (between operating temperature limits)

Analog voltage output version on
the measurement board

0- 5 V output (hardware option)
3 configurable outputs
Minimum load: 10 KOhm
Sensitivity: 5 mV
Accuracy: ± 0.5% (between operating temperature limits)

Measurement alarm relays on the

measurement board

Three alarm relays 1A-30 VAC or 0.5A-50 VDC on a resistance load
Configurable to Normally Open [NO] or Normally Closed [NC] contacts by changing the
jumper positions.

WA R N I N G

Potential Electrocution Hazard. Connect only safety low voltage < 33 VAC RMS.

System alarm relay on the main
board

One "instrument system alarm" relay per instrument
1A-30 VAC or 0.5A-50 VDC on a resistance load
Normally closed [NC] (NO relay also available) when instrument is turned on. Opens when
a system alarm is detected, and when it does not receive any signal.

WA R N I N G

Potential Electrocution Hazard. Connect only safety low voltage < 33 VAC RMS.

Digital communication

RS485
Profibus DP (optional)
Ethernet
USB-host to download data with a USB memory stick

«
...
10
11
12
13
14
...
»

Содержание ORBISPHERE K-M1100





















































































































Отзывы:

Нет отзывов

Похожие инструкции для ORBISPHERE K-M1100

Бренд: QUIETON Страницы: 24

Бренд: Quest Engineering Страницы: 24

Бренд: Nauticam Страницы: 2

Бренд: CAME Страницы: 4

DWSC - Vintage C

Бренд: Daikin Страницы: 57

Бренд: Dataradio Страницы: 72

Бренд: Kargo Master Страницы: 13

Бренд: Kargo Master Страницы: 21

Бренд: Kargo Master Страницы: 4

Бренд: Karel Страницы: 56

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 4

SX-70 SODR-X-TRACTOR

Бренд: Pace Страницы: 2

Бренд: PAC Страницы: 8

Бренд: Labona Страницы: 12

Бренд: Uebler Страницы: 18

Бренд: Fabbri Страницы: 4

Бренд: dol sensors Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды