Hach ORBISPHERE K-M1100 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 116

background image

66

Inputs/Outputs Menu

9.1 Configure snooze

9.2 View inputs/outputs

9.3 Relays

Configure snooze

In the event of an alarm, the “snooze” button stops the instrument buzzer and returns all the relays in the
instrument to their normal state during a "snooze time".
Enter the snooze time in seconds and press

OK

.

View inputs/outputs

This view option displays the state of the 3 alarm relays (on or off), and the analog output current value
for each.

Relays

There are three measurement alarm relays and one system alarm relay for the instrument. These relays
are configurable as either standard or custom events through the instrument menu.

•

An alarm relay can be activated or deactivated

•

When the alarm is OFF, it is activated,

•

When the alarm is ON, it is deactivated

All the relays are activated as soon as the instrument is ON (but alarms are OFF). When the instrument
is OFF, the relays are deactivated, thus in this state, all alarms are ON. The logic "Relay deactivated =
Alarm ON" has been chosen for this safety reason.
When the main board does not communicate with the measurement board for more than 30 seconds, the
measurement board switches all the alarm relays and the analog output to the alarm state.

Relays configuration

The three relays can be triggered by several standard events, or a
combination of events (custom). The relays output can be used to turn on a
beacon, horn or PLC. Refer to

Connections to electronic boards on page 31

.

Note:

Relays can be set to Normally Open [NO] or Normally Closed [NC] by

changing the jumper positions on the measurement board. Refer to

Measurement alarm relays on page 32

•

Select a standard event in the rolling list

•

If “Custom event” has been selected, it has to be configured by touching
the

configure

button

•

Press on the text box to open the selection menu (rolling menu). Select
the events that must trigger the relay, and press

OK

.

Proceed in the same manner for other events that should trigger the relay.

Test channel relays

The three measurement alarm relays can be manually activated for testing
purposes:

•

Select Relay

On

,

Off

or

Not under test

.

See note regarding the relays below. “Not under test” means the relay is in
operating mode, and it will be triggered normally.

Note:

A relay set to NO will close when activated (

On

), but a relay set to NC

will open. Refer to

Measurement alarm relays on page 32

Test system relay

Similarly, the system alarm relay can be manually activated for testing
purpose.

•

Select Relay

On

,

Off

or

Not under test

.

Note:

In both the Test Channel Relays and Test System Relay options above, once the tests have been

completed press Cancel to exit the screen. At the same time, this will reset all relays (including the system
relay) back to a status of “Not under test”.

«
...
65
66
67
68
69
...
»

Содержание ORBISPHERE K-M1100





















































































































Отзывы:

Нет отзывов

Похожие инструкции для ORBISPHERE K-M1100

Бренд: Panasonic Страницы: 16

Бренд: NEC Страницы: 8

Бренд: ECO Sensors Страницы: 2

Бренд: BAC Страницы: 10

Бренд: Baby’s Journey Страницы: 2

Бренд: Nacon Страницы: 12

Wireless Temperature/Humidity Station

Бренд: DAVIS Страницы: 8

Бренд: Napoleon Страницы: 2

Бренд: S&B Filters Страницы: 7

Бренд: NEEWER Страницы: 58

Reference Series

Бренд: OEM Audio Страницы: 29

Бренд: XCM Страницы: 11

Бренд: BabySense Страницы: 76

CV MY FIRST TRAMPOLINE AND ENCLOSURE

Бренд: Chad Valley Страницы: 15

Бренд: poly-planar Страницы: 2

Бренд: Actia Страницы: 37

Бренд: FixPosition Страницы: 8

Бренд: E+E Elektronik Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды