Hach ORBISPHERE K-M1100 Скачать руководство пользователя страница 27

Страница: 27 / 116

Installation

3.4.3 Connections (bottom of instrument)

Note:

The type of power cable connection will vary depending on the instrument specification.

Alternative Instrument Mounting Procedure

When it is not convenient to work from the back of the panel, the instrument can be connected
before fitting in the panel.

Install the panel support frame in the panel opening

Slip the cables through the panel opening

Remove the instrument cover

Slip the cables through the instrument cover

Slip the cables through the instrument back panel cable glands

Connect the cables to the instrument electronic boards

Tighten the cable glands

Reinstall the instrument cover

Install the instrument in the panel opening

Figure 11 Panel mount connection panel

1 - Power cable

5 - Input/Output 1 cable gland

2 - Ethernet cable gland

6 - Sensor connection

3 - USB-A host connector for mass storage device

7 - External pressure sensor connection

4 - USB-B 4 pin connector (reserved for
manufacturing)

8 - Input/Output 2 cable gland

Содержание ORBISPHERE K-M1100





















































































































Результаты поиска

Содержание ORBISPHERE K-M1100

Отзывы:

Похожие инструкции для ORBISPHERE K-M1100

Бренды по названию

Популярные бренды

Hach ORBISPHERE K-M1100, Руководство пользователя

Результаты поиска

Содержание ORBISPHERE K-M1100

Отзывы:

Похожие инструкции для ORBISPHERE K-M1100

Бренды по названию

Популярные бренды