Hach ORBISPHERE K-M1100 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 116

background image

30

Installation

Wire the female connector as follows:

1.

Take the narrow end of the connector (4) in one hand and the main body (2) in the other
and unscrew the two. Pull away the cable clamp (3) and unscrew the end plug (1) to reveal
the four parts that make up the connector.

2.

Loosen the screws on the cable clamp (3) to allow enough room to pass the power cable
through.

3.

Pass the power cable through the end plug (1), the main body (2), and the cable clamp (3),
and then connect the three wires (live, neutral and earth) to the connector (4) as follows:

4.

Slide the cable clamp (3) back onto the connector (4) and tighten the screws on the clamp
to secure the cable.

5.

Screw the two parts (4) and (2) back together.

6.

Secure the power cable by screwing the end plug (1) back in place.

7.

The female connector can now be plugged directly into the instrument power connector. The
two connectors are grooved to avoid an incorrect fitting. Tighten the female connector to the
instrument power connector finger-tight.

1) Live (brown)

2) Neutral (blue)

3) Not used

Earth (green and yellow)

Note:

The numbers and earth

symbol are stamped on the end of
the connector. Ensure it is connected
correctly.

«
...
29
30
31
32
33
...
»

Содержание ORBISPHERE K-M1100





















































































































Отзывы:

Нет отзывов

Похожие инструкции для ORBISPHERE K-M1100

Бренд: Idis Страницы: 2

Бренд: YEAZ Страницы: 60

Бренд: T-up Страницы: 14

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 4

SX-70 SODR-X-TRACTOR

Бренд: Pace Страницы: 2

Бренд: PAC Страницы: 8

Бренд: Burley Страницы: 16

Бренд: Nauticam Страницы: 33

FDSB5481 Series

Бренд: Viking Страницы: 54

Бренд: Hama Страницы: 75

Бренд: EUFAB Страницы: 4

Бренд: CYBEX Страницы: 24

Alarm Clock Camera Case

Бренд: Wasserstein Страницы: 10

Бренд: Takex Страницы: 20

The Professional

Бренд: SLIK Страницы: 2

Бренд: Linear Страницы: 3

Бренд: VIKING BAGS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды