Hach ORBISPHERE K-M1100 Скачать руководство пользователя страница 40

Страница: 40 / 116

Section 4

User Interface

4.1 Instrument

The instrument front panel provides these user interfaces:

•

Touch screen acting as display, touch pad and keyboard. Contrast can be adjusted.

•

LED, showing when the instrument is on.

•

A buzzer which sounds each time the screen is touched, and when an event alarm is set.

Turning Instrument On and Off

There is no power switch on the instrument. The mains must be disconnected to turn the
instrument off. The LED indicates when the instrument is on.

Measurement window

The main (numeric) measurement window continuously displays:

•

Sensor numeric values

•

Measured sensor trends (for the last 10 minutes to last hour)

•

Measured sensor data alarm limits and other events

•

Temperature

4.2 Touch screen

The user interface on the front panel is a 320x240 pixels display with touch screen. To make
navigation user friendly, the interface software is Windows CE based, providing easy selection
through menus.

Touching some items on the display calls a related function, similar to a shortcut.

4.2.1 Function keys on the header bar

Figure 25 Numeric view

All the measurement, configuration, calibration and "standard
service" routines can be called by pressing buttons and menu
bars on screen.

Measurement display shows one measurement slope.

Display can be configured to only show a sensor
measurement, or to show a parametrized graphic
representation of the last measurements.

Shortcut to the user login window. Pressing this button for more than
2 seconds calls the ID and password window. Refer to

Identification

and authorization level on page 42

•

Closed padlock indicates that the touch screen is locked.

•

Open padlock indicates that the instrument is in view mode only,
but no user is logged in (level 0).

•

When a user is logged in, this box show the authorization level of
this user as 1, 2, 3 or 4 (4 being the highest, refer to

User

management on page 92

Содержание ORBISPHERE K-M1100





















































































































Результаты поиска

Содержание ORBISPHERE K-M1100

Отзывы:

Похожие инструкции для ORBISPHERE K-M1100

Бренды по названию

Популярные бренды

Hach ORBISPHERE K-M1100, Руководство пользователя

Результаты поиска

Содержание ORBISPHERE K-M1100

Отзывы:

Похожие инструкции для ORBISPHERE K-M1100

Бренды по названию

Популярные бренды