Hach ORBISPHERE K-M1100 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 116

background image

54

Measurement Menu

Measurement alarms configuration

Set the thresholds for the low/high concentration levels, according to the application. Each alarm type
can be individually enabled or disabled without losing its settings.
These events can activate the relays and can be displayed.

•

Low-low

: 2nd stage for too low concentration

•

Low

: 1st stage for too low concentration

•

High

: 1st stage for too high concentration

•

High-high

: 2nd stage for too high concentration

•

Hysteresis

: A percentage of the above concentration values. The hysteresis is used to prevent relay

“flickering” when the measurement is just at the alarm levels. Set this to a minimum, but enough to
eliminate flickering.
As an example, if the High Alarm is set to 40 units and the Hysteresis is set to 10%, then the High
Alarm is activated once the measurement reaches 40 units, but only deactivated once the
measurement drops below 36 units. With the Low Alarm the opposite is true, in that if the Low Alarm
is set to 20 units and the Hysteresis set to 10%, then the Low Alarm is activated when the
measurement drops below 20 units, and deactivated when the measurement rises above 22 units.

•

Delay

: The delay in seconds, before alarms go on whenever concentration values go above ”High

alarms” or below “Low alarms”. Set this to a minimum value, but enough to avoid alarms for
non-representative peaks beyond the set level.

Figure 37 Alarms system diagram

«
...
53
54
55
56
57
...
»

Содержание ORBISPHERE K-M1100





















































































































Отзывы:

Нет отзывов

Похожие инструкции для ORBISPHERE K-M1100

Бренд: Veris Industries Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Barco Страницы: 25

Бренд: Barco Страницы: 16

Бренд: Dakota Digital Страницы: 2

Бренд: Dakota Digital Страницы: 6

Бренд: Dakota Digital Страницы: 7

Бренд: Dakota Alert Страницы: 2

Бренд: Kathrein Страницы: 52

HOIST-A-TOP JL CRANK

Бренд: Lange Originals Страницы: 13

Бренд: Quadratec Страницы: 8

Бренд: QVS Страницы: 1

Бренд: Valcom Страницы: 1

Бренд: Valcom Страницы: 13

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 4

Бренд: Zagg Страницы: 2

Canon C100 Z-Finder

Бренд: Zacuto Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды