background image

Product group and series

Voltage rating

Power rating [kW (hp)]

VLT® HVAC Drive FC 102
VLT® Refrigeration Drive FC 103
VLT® AQUA Drive FC 202

(T4) 380–480 V

110–160 (150–250)

(T7) 525–690 V

75–160 (75–200)

VLT® AutomationDrive FC 302

(T5) 380–500 V

90–132 (125–200)

(T7) 525–690 V

 

55–132 (60–150)

1.2 Kit Number

Table 2: Number for 300 A Current Sensor Kit

Kit number

Kit description

176F6516

300 A Current Sensor Conversion Kit for D1h/D3h/D5h/D6h

1.3 Items Supplied

Table 3

 provides a list of items included in the 300 A current sensor kit. Refer also to 

Illustration 4

.

Table 3: Items Supplied in 300 A Current Sensor Kit

Item

Quantity

EMC shield

1

M8 flange nut

3

M5x16 countersunk screw

3

Terminal plate

3

R/S/T terminal label

1

M10x30 machine screw

6

M10 hex nut

6

Mains terminal block

1

M5x12 screw

11

M5x16 thread-forming screw

3

U/V/W terminal label

1

Motor terminal block

1

AN275538690239en-000101 / 130R0721 | 1

Danfoss A/S © 2022.11

Installation Guide

300 A Current Sensor Kit for 

D1h/D3h/D5h/D6h 

Drives

VLT® FC Series FC 102, FC 103, FC 202, FC 302

1 Overview

1.1 Description

The 300 A current sensor kit contains all components required to upgrade the current sensor assembly in D1h/D3h/D5h/D6h drives.

 

The kit is compatible with the power ratings shown in 

Table 1

. The power rating of the drive is listed on the nameplate as characters

 

7–10 of the type code (T/C).

Table 1: Applicable Power Range for 300 A Current Sensor Kit

Содержание 176F6516















Отзывы: