Grizzly G1023RL Скачать руководство пользователя страница 31

Страница: 31 / 96

Model G1023RL Series (Mfd. Since 12/11)

-29-

Blade Requirements

To ensure that the spreader or riving knife works
safely, the following requirements MUST be met
when installing new blades:

• Blade Diameter: 10"
• Spreader/Riving Knife Thickness: 0.98"–0.102"

(2.5–2.6mm)

• Required Blade Body Thickness (excluding

teeth): 0.086"–0.094" (2.2–2.4mm)

• Required Blade Kerf Thickness: 0.122"– 0.129"

(3.1mm–3.3mm)

The spreader or riving knife MUST be aligned/
adjusted to blade. These requirements do not
apply to dado blades.

Figure 35. Crosscutting blade.

Figure 36. Combination blade.

Crosscut blade features:
•

Best for cutting across the grain

•

60-80 teeth

•

Alternate top bevel tooth profile

•

Small hook angle and a shallow gullet

Alternate

Top

Bevel

Combination blade features:
•

Designed to cut both with and across grain

•

40-50 teeth

•

Alternate top bevel and flat, or alternate top
bevel and raker tooth profile

•

Teeth are arranged in groups

•

Gullets are small and shallow (similar to a
cross-cut blade), then large and deep (similar
to a ripping blade

Alternate

Top

Bevel

and
Flat

Blade Selection

Figure 34. Ripping blade.

This  section  on  blade  selection  is  by  no  means
comprehensive.  Always  follow  the  saw  blade
manufacturer's  recommendations  to  ensure  safe
and efficient operation of your table saw.

Ripping Blade Features:
•

Best for cutting with the grain

•

20-40 teeth

•

Flat-top ground tooth profile

•

Large gullets for large chip removal

Flat

Top

Blade

Содержание G1023RL

































































































Результаты поиска

Содержание G1023RL

Отзывы:

Похожие инструкции для G1023RL

Бренды по названию

Популярные бренды

Grizzly G1023RL, Руководство пользователя

Результаты поиска

Содержание G1023RL

Отзывы:

Похожие инструкции для G1023RL

Бренды по названию

Популярные бренды