Grizzly G1023RL Скачать руководство пользователя страница 28

Страница: 28 / 96

-26-

Model G1023RL Series (Mfd. Since 12/11)

SECTION 4: OPERATIONS

Damage to your eyes, lungs, and hearing

could result from using this machine without

proper protective gear. Always wear safety

glasses, a respirator, and hearing protection

when operating this machine.

For Your Own Safety Read Instruction

Manual Before Operating Saw

a) Wear eye protection.

b) Use saw-blade guard and riving knife for

every operation for which it can be used,

including all through sawing.

c) Keep hands out of the line of saw blade.

d) Use a push-stick when required.

e) Pay particular attention to instructions

on reducing risk of kickback.

f) Do not perform any operation freehand.

g) Never reach around or over saw blade.

NOTICE

If you have never used this type of machine

or equipment before, seek training from an

experienced machine operator or read "how

to" books before beginning any projects.

Regardless of the content in this section,

Grizzly Industrial will not be held liable for

accidents caused by lack of training.

To reduce the risk of

serious injury when using

this machine, read and

understand this entire

manual before beginning

any operations.

ON/OFF Switch: Starts and stops the motor.

Switch Disabling Lock: When installed, disables
the switch to prevent accidental startup.

Basic Controls

Blade Height Handwheel: Adjusts blade height.

Blade Height Lock: Locks the blade height.

Fence Lock: Locks and unlocks fence position.

Blade Tilt Handwheel: Adjusts the blade angle.

Blade Tilt Lock: Locks blade tilt handwheel so it
does not move during operations.

Figure 30. Basic table saw controls.

Blade Tilt

Handwheel

Blade Height

Handwheel

Blade Height

Lock

Blade Tilt

Lock

Fence

Lock

Figure 29. ON/OFF switch with disabling lock.

Shaft

Padlock

START

Button

OFF

STOP

Paddle

Содержание G1023RL

































































































Результаты поиска

Содержание G1023RL

Отзывы:

Похожие инструкции для G1023RL

Бренды по названию

Популярные бренды

Grizzly G1023RL, Руководство пользователя

Результаты поиска

Содержание G1023RL

Отзывы:

Похожие инструкции для G1023RL

Бренды по названию

Популярные бренды