Grizzly G1023RL Скачать руководство пользователя страница 25

Страница: 25 / 96

Model G1023RL Series (Mfd. Since 12/11)

-23-

4. Use (2)

⁄

"-16 x

⁄

" hex bolts and

⁄

" flat

washers to loosely attach the braces to the
legs. (These will be adjusted and fully tight-
ened later.)

5. Use the (2)

⁄

" x

⁄

" wood screws and

⁄

" flat

washers to attach the braces to the extension
table, as shown in

Figure 24.

6. Tighten the bolts that hold the braces.

7. Adjust the extension table so it is flat (both

flush and parallel) with the main table. This
can be done by loosening the mounting bolts
and adjusting the feet up/down as needed.

Figure 25 shows the extension table installed
on the saw.

Figure 25. Extension table installed.

8. Tighten the extension table mounting bolts.

Tighten the hex nuts on the feet against the
legs so they will not move.

Install the saw blade as outlined in

Blade

Installation on Page 30.

Saw Blade

To install the table insert:

1. Install the table insert into the opening of the

table saw over the blade.

2. Adjust the table insert set screws to make

sure the insert is flush with the table, using a
straightedge as a guide, (see

Figure 26).

Table Insert

Figure 26. Adjusting insert flush with table.

3. Follow instructions in Checking Fence

Parallelism, then proceed to Blade Guard
to complete the remaining assembly steps.

Checking Fence

Parallelism

Verify that the fence is parallel to the blade/miter
slot and that this setting did not change dur-
ing shipping (refer to "Clamping Pressure and
Parallelism" on

Page 67). The blade was set par-

allel with the miter slot at the factory—this affects
whether the fence is parallel when mounted to the
table.

Blade Guard

Install the blade guard as instructed in "Installing
Blade Guard & Spreader" on

Page 31.

Содержание G1023RL

































































































Результаты поиска

Содержание G1023RL

Отзывы:

Бренды по названию

Популярные бренды

Grizzly G1023RL, Руководство пользователя

Результаты поиска

Содержание G1023RL

Отзывы:

Бренды по названию

Популярные бренды