manualshive.com logo in svg

Grizzly G1023RL, Руководство пользователя

Поделиться
Скачать
Grizzly G1023RL Скачать руководство пользователя страница 24

-22-

Model G1023RL Series (Mfd. Since 12/11)

Install the router table and legs now on the Model 
G1023RLW or G1023RLWX using the instructions 
provided for the router table extension.

Router Table & Legs

2.  Thread the feet into the legs, place the legs 

under the table, and thread the feet out until 
the top of each leg is against the underside 
corner of the table.

Figure 23. Extension table installed.

Extension Table & 

Legs

To install the Model G1023RLX extension table 

and legs:

1.  With  the  help  of  another  person  to  hold  the 

extension table, use the (8) 

3

⁄

8

"-16 x 1

3

⁄

4

" hex 

bolts,  (16) 

3

⁄

8

"  flat  washers,  and  (8) 

3

⁄

8

"  hex 

nuts to secure the extension table to the rails, 
as shown in 

Figure 23.

Install the rear rail, front rail, rail tube, and Shop 
Fox  Classic  Fence  now,  using  the  instructions 
provided  with  the  fence.  Make  sure  the  fence 
slides  smoothly  along  the  fence  rails  and  that 
there  is  a 

1

⁄

16

"  gap  between  the  bottom  of  the 

fence and the top of the table from front to back. 
After  tightening  the  rail  mounting  bolts,  remove 
the fence for now.

Rails & Fence

3.  Use the (4) 

1

⁄

4

"-20 x 

1

⁄

2

" hex bolts and 

1

⁄

4

" flat 

washers  to  fasten  the  legs  to  the  underside 
corners  of  the  extension  table,  as  shown  in 

Figure 24.

Figure 24. Leg and brace mounted.

Leg

1

⁄

4

" x 

3

⁄

4

"

Wood Screw & 

1

⁄

4

" Flat Washer

Brace

3

⁄

8

"-16 x

 3

⁄

4

" Hex Bolt 

& 

3

⁄

8

" Flat Washer 

(Not Shown)

1

⁄

4

"-20 x 

1

⁄

2

" Hex Bolt 

& 

1

⁄

4

" Flat Washer 

4.  Use  (2) 

3

⁄

8

"-16  x 

3

⁄

4

"  hex  bolts  and 

3

⁄

8

"  flat 

washers  to  loosely  attach  the  braces  to  the 
legs. (These will be adjusted and fully tight-
ened later.)

5.  Use the (2) 

1

⁄

4

" x 

3

⁄

4

" wood screws and 

1

⁄

4

" flat 

washers to attach the braces to the extension 
table, as shown in 

Figure 24 above.

Содержание G1023RL

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды