manualshive.com logo in svg

Grizzly G1023RL, Руководство пользователя

Поделиться
Скачать
Grizzly G1023RL Скачать руководство пользователя страница 48

-46-

Model G1023RL Series (Mfd. Since 12/11)

5"

5"

 4" Slot

(Top View)

(Side View)

3

/

8

"

Countersink on Bottom

1

/

4

" Hole

Figure 68. Miter bar pattern.

5.  Cut a miter bar that will fit in the table miter 

slot  approximately  5"  long,  as  shown  in 

Figure 68. 

6.  Drill a 

1

⁄

4

" hole in the center of the bar, then 

countersink the bottom to fit a 

1

⁄

4

"-20 flat head 

screw. 

7.  Mark a 4" line through the center of the coun-

tersunk hole, then use a jig saw with a narrow 
blade to cut it out.

8.  Assemble  the  miter  bar  and  featherboard 

with  a 

1

⁄

4

"-20  x  flat  head  screw,  flat  washer, 

and  a  wing  nut  or  a  star  knob  (see 

Figure 

69).  Congratulations!  Your  featherboard  is 
complete.

4.  Rout  a 

1

⁄

4

"–

3

⁄

8

"  wide  slot  4"–5"  long  in  the 

workpiece and 1"–2" from the short end of the 
featherboard (see 

Figure 67).

Figure 67. Slot routed in featherboard.

1"-2"

4"-5"

1

/

4

"-

3

/

8

"

 Slot

(Side View)

Wing Nut

Miter Bar

Featherboard

Flat Head Screw

Flat Washer

Figure 69. Assembling miter slot featherboard 

components.

 

Tip: The length of the flat head screw depends 
on the thickness of the featherboard—though 
1

1

⁄

2

" to 2" lengths usually work.

 
 

Now, proceed to 

Mounting Featherboard in 

Miter Slot on Page 47.

 Note: The routed slot, countersink hole, and 

the flat head screw are essential for the miter 
bar to clamp into the miter slot. When the 
wing nut is tightened, it will draw the flat head 
screw upward into the countersunk hole. This 
will spread the sides of the miter bar and 
force them into the walls of the miter slot, 
locking the featherboard in place.

 

Tip: Consider making the miter bar longer for 
larger featherboards—approximately half the 
length of the total featherboard—to support 
the force applied to the featherboard during 
use.

Содержание G1023RL

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды