Grizzly G1023RL Скачать руководство пользователя страница 76

Страница: 76 / 96

-74-

Model G1023RL Series (Mfd. Since 12/11)

21. Re-install the larger front spacer and key onto

the arbor. The arbor should look like the one
shown in

Figure 136.

22. Lift the motor to its maximum elevation, then

secure the motor adjustment bolt.

23. Place the belt onto the bottom motor pulley,

then wrap the belt around the arbor housing
bracket above it.

24. Place the arbor pulley between the arbor

housing brackets, slide the belt over the
pulley, then insert the arbor into the pulley, as
shown in

Figure 137.

Figure 136. Components re-installed on arbor.

Figure 137. Re-installing arbor and belt.

Arbor Pulley

Belt

Arbor

Housing

Brackets

27. Use a block of wood to seat a new 6203-2RS

bearing (Part P1023RL100) into the end of
the arbor.

28. Thread the lock nut onto the arbor shaft,

place the open end of the arbor wrench on
the arbor, and use a 25mm wrench to tighten
the nut so it is snug, but not too tight.

29. Re-install the bearing retainer with the three

Phillips head screws removed earlier.

30. Tighten the pulley set screws shown in

Figure 131 on Page 73.

31. Check the position of the belt on the pulley

sheaths; adjust if necessary so it is cen-
tered.

32. Tension the belt (refer to the instructions on

Page 71).

33. Re-install the mounting plate and dust chute

with the cap screws you removed earlier.

34. Replace the shims at the locations from

which they came.

35. With the help of another person, lift the table

and place it on top of the cabinet. Align the
mounting holes in the table and cabinet, then
secure the table with the mounting bolts.

36. Re-install the table insert and close the motor

cover.

37. Verify that the blade and miter slot are par-

allel at 90° and 45° (refer to instructions on

Page 61).

38. Raise the blade all the way up, then tilt the

blade to 45°.

— If the blade does not touch the insert no

further adjustments need to be made.

— If the blade touches the insert, loosen the

table mounting bolts, adjust the table until
the blade does not touch the insert, then
tighten the mounting bolts. Re-check miter
slot to blade parallelism and adjust as
needed.

25. Tap the arbor shaft into the pulley, making

sure the shaft is straight.

26. Install the rear spacer onto the end of the

arbor.

Spacer

Bearing

Key

Содержание G1023RL

































































































Результаты поиска

Содержание G1023RL

Отзывы:

Бренды по названию

Популярные бренды

Grizzly G1023RL, Руководство пользователя

Результаты поиска

Содержание G1023RL

Отзывы:

Бренды по названию

Популярные бренды