GREAT PLAINS YP2425 Скачать руководство пользователя страница 83

Страница: 83 / 166

YP2425 and YP2425F

Table of Contents

Index

Adjustments

2016-11-16

Table of Contents

Index

401-406M

Refer to Figure 111

Note:

With the seed meter wheel removed, you may

want to check the meter for internal damage or
trash.

Note:

Some wear on top edge of slide

is normal.

Excess wear is cause for replacement.

When changing crops be sure to clean out air
system before installing new meters or wheels. See
“

Cleaning Out Air System

” on page 96.

Place new wheel on meter wheel shaft. Tilt it slightly
forward to engage and push back on the slide. Seat
wheel fully on cross-pin.

Replace spring-loaded wheel retainer. Make

turn

to seat cross-pin in shallow groove of retainer.

Meter Installation

Installation is the reverse of the removal process, with
two steps omitted.

Refer to Figure 112

Insert the meter.

Insert the top meter tab (with the hook).
Align the meter base with the latch plate ears.
Insert the bottom meter tab.

Mind the lower latch, as it tends to swing under the
meter base and block mating with the latch plate.

Refer to Figure 104 on page 76

Engage the upper latch, and swing the mounting
plate into engagement with the meter.

Note:

Always engage upper latch first.

Refer to Figure 105 on page 76

Engage the lower latch.

Refer to Figure 106 on page 77

Slide the seed hose over the meter inlet tube, and
then slide the retaining ring down the seed hose.

Figure 111

Inspect Meter

22884

Figure 112

Install Meter

25275

1
2
3

Содержание YP2425







































































































































































Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды

GREAT PLAINS YP2425, Руководство оператора

Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды