GREAT PLAINS YP2425 Скачать руководство пользователя страница 152

Страница: 152 / 166

2016-11-16

Table of Contents

Index

401-406M

YP2425 and YP2425F

Table of Contents

Index

Appendix R - Row-Pro™

148

Row-Pro™ Components

Refer to Figure 148 and Figure 149

The main systems of Row-Pro™ consist of:

An air compressor system:

one 12VDC air

compressor

with air tank

, two extension

cables

, and one fuse assembly

A load sensing system:

DPLCM (Down Pressure

Load Cell Module)

and the load cells

An adjusting system:

valves

and air

cylinders

Load Cell, DPLCM and Valves

The DPLCM

and valves

are mounted together on

a plate and are connected to the DICKEY-john

Row-Pro™ wiring harness

Two leads on the Row-Pro™ harness each connect to a
load cell

which is located in the opener body (see

fig.162). Four leads connect to the valve sets. There is
one pair (one air intake, one exhaust) for each valve.

Note:

For single row planters:

There is one load cell and one valve set per each
opener section located at mid section.

Note:

For twin row planters:

There are two load cells and two valve sets per
each opener section located on the long and
short center row unit of the section.

The Row-Pro™ harness connects to the planter’s
CANbus at connector ends

The load cell provides feedback so the system can
maintain the target pressures.

The DPLCM uses the readings from the load cell to
regulate the air valves in order to increase or decrease
pressure in the air cylinders.

Figure 148

Row-Pro™ Components

31878

Figure 149

Load Cell Location (Opener)

32089

load cell

Содержание YP2425







































































































































































Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды

GREAT PLAINS YP2425, Руководство оператора

Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды