GREAT PLAINS YP2425 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 166

background image

YP2425 and YP2425F

Table of Contents

Operating Instructions

27

2016-11-16

Table of Contents

401-406M

Unfolding The YP24

The distance between the tractor and the seed structure
decreases by 12 feet (3.7 m) during unfolding. Planter,
tractor, or both will move during this operation.

Crushing, Pinch-Point and Overhead Hazards:
To prevent serious injury or death:



Fold only on hard level ground. Allow ample room.



If it is desired that the tractor not move, make sure tractor
is in Park and/or has parking brakes set, otherwise the
telescoping movement of the planter is likely to result in
tractor movement.



Do not allow anyone to be on or near the planter during
unfolding.



Stay clear of the wing sweep arcs. The sweep arcs of the
wings have numerous pinch and crush points in the
mechanism. Coulters and row openers are sharp.



Allow no one near planter. The seed structure usually
moves forward during unfolding.



Do not unfold with planter lowered, or machine damage
will result.



Unfold only with markers resting in transport cradles.



Unfold only if hydraulics are bled free of air and fully
charged with hydraulic oil.

1.

Move to level ground.

Refer to Figure 19

2.

On the Clutch Folding Module (CFM), set the
following switches to OFF (down):
MASTER switch

in the CLUTCH cluster

, and

Fert.Pump

.

3.

If the folded planter is lowered, raise mainframe (see
“

Raising/Lowering Planter

” on page 29).

4.

If equipped with hydraulic hitch, the CFM Lift/Hitch
switch

must be set to Hitch.

Refer to Figure 20

5.

At each wing caster, check that lock control
handles

and indicators

are in the ROAD

position, allowing the casters to swivel. If they are
not, set handle to ROAD position and fully raise and
lower planter to release load on lock plates to allow
them to come open.

Refer to Figure 19

6.

Set CFM Marker/Fold switch

to Fold. LED above

switch blinks continuously.

Figure 19

Clutch Folding Module

26111

2

1

3

4

5

Figure 20

Caster Unlocked

29306

6

7

1

2

3

5

6

7

4

«
...
29
30
31
32
33
...
»

Содержание YP2425







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP2425

Бренд: EarthQuake Страницы: 36

Бренд: Walker Страницы: 100

Бренд: AL-KO Страницы: 116

Бренд: Gardenline Страницы: 30

Бренд: Skil Страницы: 104

Бренд: Alamo Страницы: 99

Бренд: Swisher Страницы: 16

Бренд: Baroness Страницы: 66

Swift S2 MJ71-190

Бренд: Major Страницы: 54

Бренд: Spearhead Страницы: 32

Бренд: Ferris Страницы: 60

Pro Force Groundsmaster 3280-D

Бренд: Toro Страницы: 8

Бренд: Yard-Man Страницы: 28

Бренд: Jacobsen Страницы: 92

Бренд: GGP ITALY Страницы: 176

RS seriesMS series

Бренд: Robomow Страницы: 4

Бренд: Robomow Страницы: 84

Бренд: Husqvarna Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды