GREAT PLAINS YP2425 Скачать руководство пользователя страница 90

Страница: 90 / 166

2016-11-16

Table of Contents

Index

401-406M

YP2425 and YP2425F

Table of Contents

Index

Troubleshooting

General Troubleshooting

Problem

Cause

Solution

Planting too
little

Incorrect seed size for meter wheel can
cause skips

Replace meter wheels to match seed

Meter drive not engaged

Engage drive coupler, page 69

Worn meter components

Replace worn components

Incorrect seed rate.

Check seed rate information.

Excessive field speed.

Reduce field speed.

Seed size and weight may vary.

Finger meter brush may need adjustment, page 80.

Incorrect tire size or air pressure.

Correct tire size and air pressure, page 121.

Incorrect fan air flow

Adjust fan speed and/or fan baffle, page 59

Excessive gaps between planter passes.

Adjust marker, page 53.

Plugged row-unit seed tube.

Raise planter, expose bottom of seed tube and clean out.

Thrown or worn drive chains

Check drive chains.

Worn/rusted sprockets, chains and/or chain
idlers.

Replace sprockets, chains and/or chain idlers.

Improper sprocket.

Check sprockets

Speed sensor calibration

Perform calibration per DICKEY-john

documentation with

planter lowered.

Speed sensor angle.

With planter lowered, check radar speed sensor angle per
DICKEY-john

recommendations.

Meter wheel or finger pickup has fewer cells
than indicated on seed rate chart.

Charts are based on either 6 finger or 12 finger meters or
various wheel cell counts.

Planting too
much

Incorrect seed size for meter wheel can
cause doubles

Replace meter wheels to match seed

Worn meter components

Replace worn components

Meter clean-out door left open

Close door

Incorrect seed rate.

Check seed rate information in the seed monitor manual.

Actual field size is different.

Verify field size.

Excessive overlap.
Irregular shaped field.

Adjust marker, page 53.

Incorrect tire size or air pressure.

Correct tire size and air pressure, page 125.

Improper sprocket.

Check sprockets

Speed sensor calibration

Perform calibration per DICKEY-john

documentation with

planter lowered.

Speed sensor angle.

With planter lowered, check radar speed sensor angle per
DICKEY-john

recommendations.

Brush too loose on finger pickup meter

Adjust brush, page 80

Meter wheel or finger pickup has more cells
than indicated on seed rate chart.

Charts are based on either 6 finger or 12 finger meters or
various wheel cell counts.

For planters equipped with Row-Pro™, see also
“

Row-Pro™ Troubleshooting

” on page 153.

Содержание YP2425







































































































































































Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды

GREAT PLAINS YP2425, Руководство оператора

Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды