GREAT PLAINS YP2425 Скачать руководство пользователя страница 93

Страница: 93 / 166

YP2425 and YP2425F

Table of Contents

Index

Troubleshooting

2016-11-16

Table of Contents

Index

401-406M

Airbox Troubleshooting

Speed
Reading
Doesn’t Match
Tractor

Monitor speed reading will only match tractor
with planter lowered.

If speeds don’t agree during planting (with planter lowered),
re-calibrate radar speed sensor with planter lowered.

Problem

Cause

Fix

Single row doesn’t fill or keep up
with other rows.

Y tube is bent/angled off feed pipe.

Loosen and rotate pipe so the bend is straight
down and Y-tube is not pointing to front or rear
of air pipe.

Both rows on one meter outlet
low or not keeping up with other
rows.

Note:

This is more likely to

occur on end outlets.

Blockage in air slot in top of airbox.

Clear by using a long slim tool and taking
hose off hose outlet or clean-out door.

Note:

May be necessary to take top off

airbox to clear debris from slot,
or use side access doors.

Bad hose routing between delivery
hose and airbox on wing.

Correct hose routing.

Multiple rows fail for lack of seed.

Fan speed too high/too low.

Check/adjust fan speed, butterfly valve.

Out of seed.

Add seed.

Single or multiple hoses
plugging just ahead of airbox.

Fan speed too high/too low.

Check/adjust fan speed, butterfly valve.

Possible air leak.

Check for air leak downstream between box
and top of meter.

All rows fail.

Lack of seed.

Add seed.

Fan speed too high.

Adjust fan speed or butterfly valve.
Extremely high populations may require
slightly reduced field speed.

1, 2, 3, or more outlets fail.

Note:

Outlets can be

side-by-side or random.
Plugging may also move
from one outlet to
another.

Foreign matter in seed chamber in
bottom of airbox.

Clean out seed chamber.

Incorrect airbox air slot to seed
chamber.

Contact Great Plains Service dept. for
assistance.

Little or no seed to many rows,
with heavily treated seed.

Seed treatment sticky.

Note:

Do not use liquid seed

treatments.

Add talc to seed to dry out seed treatment.

Treatment mixed unevenly and
plugging outlets.

Clean out seed. Re-mix seed and treatment.

Problem

Cause

Solution

Содержание YP2425







































































































































































Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды

GREAT PLAINS YP2425, Руководство оператора

Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды