GREAT PLAINS YP2425 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 166

background image

YP2425 and YP2425F

iii

2016-11-16

401-406M

©

Copyright 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2014, 2015, 2016 All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been
taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed
for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products
as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Trademarks of Great Plains Manufacturing, Inc. include: AccuShot, Max-Chisel, Row-Pro,

Singulator Plus, Short Disk, Swath Command, Terra-Tine, Ultra-Chisel, and X-Press.

Registered Trademarks of Great Plains Manufacturing, Inc. include: Air-Pro, Clear-Shot, Discovator, Great Plains, Land Pride, MeterCone,

Nutri-Pro, Seed-Lok, Solid Stand, Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo-Max, Turbo-Till, Ultra-Till, Whirlfilter, and Yield-Pro.

Brand and Product Names that appear and are owned by others are trademarks of their respective owners.

Printed in the United States of America

Table of Contents

Important Safety Information.................................................1

Safety Decals ....................................................................6

Introduction...........................................................................12

Document Family .....................................................12

Description of Unit ...........................................................12

Intended Usage ........................................................12

Models Covered ..............................................................12
Using This Manual...........................................................12

Definitions.................................................................12

Owner Assistance............................................................13
Further Assistance...........................................................13

Preparation and Setup .........................................................14

Post-Delivery/Seasonal Setup.........................................14
Pre-Planting Setup ..........................................................14
Hitching Tractor to Planter...............................................15

If Weight Transfer is Installed...................................15
Hitching with 3-Point.................................................16
Hitching with Hydraulic Tongue (Option)..................16
Raising/Lowering Tongue.........................................17
Local Float on Hydraulic Tongue..............................17

Hydraulic Hose Hookup...................................................17

Protecting Fan Hydraulic Motor Seals......................19

Electrical Hookup.............................................................20

Store Main Parking Stand ........................................20
Storing 3-Point Parking Stands ................................21
Tank Cart Hitching....................................................21
Fertilizer Connection Types......................................21
Making Fertilizer Connections ..................................22

Heights and Leveling .......................................................22

Set Tongue Height ...................................................22
Checking Planter Leveling Side to Side ...................23
Center Section Level Check.....................................23

Wing Leveling ..................................................................24

Wing Leveling, Inboard End .....................................24
Wing Leveling, Outboard End ..................................24

Lock Up Fertilizer Drive ...................................................25

Operating Instructions .........................................................26

Pre-Start Checklist...........................................................26
Unfolding The YP24 ........................................................27
Raising/Lowering Planter.................................................29

Local Float on Hydraulic Tongue..............................29
Raising Planter .........................................................30
Lowering Planter ......................................................30

Folding the YP24 .............................................................31

Re-phasing Fold System ..........................................33

Lift Cylinder Lock-Up................................................33
Re-Phasing Lift System............................................33

Transporting the Planter..................................................34

Transport Checklist ..................................................35
Steering....................................................................35

Field Set-Up Checklist.....................................................36
Field Operation................................................................38
Marker Unfolding .............................................................39

Marker Unfold (one side)..........................................40
Row Marker Operation .............................................40
Folding the Markers .................................................40
Unusual Marker Operations .....................................40
Both Sides Unfolded ................................................40

Monitor Operation............................................................40
Planting ...........................................................................41
Electric Clutch Operation.................................................42

Clutch Switch Coverage...........................................42
Electric Clutch Lock-Up............................................42

Swath Command™ Clutch Operation .............................43
Weight Transfer Operation (Option) ................................43
Y-Tubes...........................................................................44
Airbox Operation .............................................................44

Fan Operation ..........................................................44

82 Bu. Hopper Operation ................................................45

Adding Seed to 82 bu. Hopper.................................45

Changing the Seed Box or 82 Bu. Hopper ......................46
Checking Planting Rate...................................................47
Auxiliary Hydraulics .........................................................48

Operating Auxiliary Hydraulics .................................48

Trailer Operations............................................................49
Short-Term Parking .........................................................50
Long-Term Storage .........................................................51

Adjustments..........................................................................52

Gauge/Transport Wheel Adjustments .............................53
Marker Adjustments ........................................................53

Marker Disk Adjustment ...........................................54
Marker Extension .....................................................54
Marker Gauge Wheel Adjustment ............................55
Marker Shear Bolt Replacement ..............................55
Marker Chain Length Adjustment.............................55
Dual Marker Speed Adjustment ...............................56

Height Switch Adjustment ...............................................57
Height Switch Adjustment ...............................................58
Fan Adjustments .............................................................59
Liquid Fertilizer Setup......................................................60

«
1
2
3
4
5
...
»

Содержание YP2425







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP2425

Бренд: Gardol Страницы: 171

Бренд: Ryobi Страницы: 16

Wheel Horse XL 320 71199

Бренд: Toro Страницы: 40

BE-FM RDG Series

Бренд: AGRI EASE Страницы: 31

AMBROGIO L60 ELITE

Бренд: ZCS Страницы: 34

Бренд: Woods Страницы: 76

Бренд: Yard force Страницы: 49

Бренд: Snapper Страницы: 56

Бренд: Troy-Bilt Страницы: 48

Бренд: Toro Страницы: 4

Бренд: Tiger Страницы: 84

Бренд: Masport Страницы: 5

Бренд: Racing Страницы: 21

Four Wheel Steer Lawn Tractors

Бренд: Yard Machines Страницы: 16

Zero Turn Rotary Mower

Бренд: Jacobsen Страницы: 62

Бренд: Racing Страницы: 20

Бренд: Wards Garden Mark Страницы: 12

Бренд: Cub Cadet Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды