GREAT PLAINS YP2425 Скачать руководство пользователя страница 155

Страница: 155 / 166

YP2425 and YP2425F

Table of Contents

Index

Appendix R - Row-Pro™

151

2016-11-16

Table of Contents

Index

401-406M

Row-Pro™ Adjustments

Refer to Figure 154

Load Cell Reading

These readings are displayed and adjusted from the
IntelliAg

seed monitor console.

Control Mode:

Auto

is the normal running mode.

Manual

is used to control the valves only when the

operator touches the increase or decrease icon on the
work screen.

Monitor Only:

This screen disables control, but still

reports sensor feedback. From there, press the

Down

Pressure Diagnostic

key and then press the

Float

Mode ON

button to release all of the air from the system.

Next, press the

Float Mode OFF

button. Stay on the

Diagnostic

screen and make a planting pass. Note the

pressure displayed on the

Diagnostic

screen and then

evaluate the seed trench. If the seed trench results are
acceptable, use the displayed pressure as your target
rate.

Front-Rear Linked:

“

Enabled

” links the front and rear

row units so that the same amount of pressure
increase/decrease set at the screen is applied to
front/rear row units. When “

Disabled

”

- front/rear row

units are not linked. Two sets of buttons appear on the
screen that allow for adjustments of front and rear rates
independently.

Target Rate:

This is the desired down pressure on the

side depth wheels. The target rate to be entered is the
set rate (pounds) of the down force to determine how
much pressure is applied. The system monitors and
adjusts pressure to meet the defined rate set at this
screen.

Note:

Pressure displayed on screen and target pressure

both refer to the amount of weight carried by the
side depth gauge wheels, and not overall row unit
down pressure.

Inc/Dec: Sets the amount that the Target Rate is
changed with each key press during planting operations.

Figure 154

IntelliAg

Screen

36544

Figure 155

Float Mode ON/OFF Screens

Содержание YP2425







































































































































































Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды

GREAT PLAINS YP2425, Руководство оператора

Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды